Complete workshop & service manual with electrical wiring diagrams for Doosan DX190W Crawler Excavator. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Doosan DX190W Crawler Excavator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

“K1024513AE.pdf”
Doosan DX190W Crawler Excavator Shop Manual
K1024513AE; Serial Number 5001 and Up; 1,176 pages

TABLE OF CONTENTS
Safety
Wheel Excavator Safety .............. SP000956
Specifications
Specification for DX190W............ SP001143
General Maintenance
General Maintenance Procedures.................. SP000016
Standard Torques........................ SP000813
Upper Structure
Cabin ........................ SP001231
Counterweight........... SP001145
Fuel Tank.................. SP001146
Fuel Transfer Pump..................... SP000021
Swing Bearing........... SP001253
Swing Reduction Gear................. SP001233
Lower Structure and Chassis
Ram Lock Valve........................... SP000923
Selector Valve........... SP000926
Double Pilot Check Valve ............ SP000927
Solenoid Valve.......... SP000928
Front Axle ................. SP000929
Rear Axle.................. SP000930
Engine and Drive Train
Transmission ............ SP000962
Drive Coupling (Main Pump)........................... SP000963
Hydraulics
Hydraulic System Troubleshooting, Testing and Adjustment ............... SP001149
Accumulator.............. SP000984
Center Joint (Swivel).................... SP000919
Cylinders................... SP001098
Main Control Valve ...................... SP000966
Swing Motor.............. SP000985
Travel Motor.............. SP001110
Counterbalance Valve ................. SP000991
Main Pump & PTO....................... SP000988
Gear Pump ............... SP000989
Service Brake Supply Valve ........................... SP000990
Dozer Control Valve..................... SP000992
Steering Valve .......... SP000993
Accelerator Pedal Valve (Hydraulic) ............... SP000964
One Spool Valve.......................... SP000996
Remote Control Valve (Work Lever / Joystick) .................. SP000069
Breaker EPPR Valve (Opt) .......... SP000192
Service Brake Pedal Valve .......... SP001006
Solenoid Valve Assembly ............ SP000997
Hydraulic Schematic.................... SP001160
Electrical System
Electrical System ......................... SP000998
Electrical Schematic .................... SP001161
Attachments
Boom and Arm.......... SP001162
Bucket....................... SP001001
…

EXCERPT:
REMOVAL
1. Look at fuel level display (Figure 2) on instrument panel in operator's cabin to see what it displays. The display is divided into ten separated segments, each representing 10
percent of total fuel supply. Also, look at level gauge on side of tank to estimate volume of fuel left in tank.
NOTE: If possible, work excavator until available fuel supply in tank has been run down as far as possible.
2. Park on firm and level ground and swing turntable to approximately a 90° with respect to wheels. See Figure 3.
3. Lower front attachment (bucket) to ground.
4. Shut down engine.
5. Set safety lever on "RELEASED" position.
6. Turn starter switch to "I" (ON) position.
WARNING: If engine must be run while performing maintenance, use extreme care. Always have one person in the cabin at all times. Never leave the cabin with the engine running.
7. Fully stroke work levers (joysticks) in all directions to relieve any pressure from accumulators.
8. Set safety lever on "LOCK" position.
9. Turn key to "O" (OFF) position and remove from starter switch.
10. Hang maintenance warning tag on controls.
11. Disconnect negative (-) battery cable leading to frame from battery.
…