Complete workshop & service manual with electrical wiring diagrams for Volkswagen Beetle, LT, T1, T2, Transporter. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Volkswagen LT, T1, T2, Transporter service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

MAKE: Volkswagen (VW)
MODEL:
YEAR: 1961 1962 1963 1964 1965 1966 1967 1968 1969 1970 1971 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 1983 1984 1985 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006

"'54-'79 Beetle & Karmann Ghia.pdf"
Type 1 Models (a.k.a. Beetle) 1200 Sedan, 1200 Convertible, 1200 Karmann Ghia Coupe, 1200 Karmann Ghia Convertible
323 pages

"'61-'65 Type 1 1200.pdf"
1,360 pages
This Volkswagen Type 1 Workshop Manual is the original service and repair information which was available in 1965. Volkswagen has constantly improved its cars, and these changes, both in parts and specifications, are often applicable to earlier models. This manual has not been updated or revised to include safety precautions, cautions or warnings, not does it include technical changes, corrections or updates that may have been made to this information since its original publication.

"'68-'76 Transporter 1600.pdf"
235 pages
All models 96.7 cu in (1584 cc)

"'68-'79 Type 2 (T2).pdf"
492 pages
Type 2 (T2) Station Wagon/Bus
Official Service Manual

"'75-'06 LT"
1 GB, English/German
Aus und Aufbauten
Manuals
Preislisten
Reisemobile
Technische Daten
Transporter
Video

"'79-'92 Transporter (DE)"
Transporter T3 Service Manual
296 pages, German
296 pages

EXCERPT:
Body and Frame
Front Axle
Fuel System
Electrical System
Engine and Clutch
Transmission and Rear Axle
Automatic Transmission
Brakes and Wheels
Lubrication and Maintenance
Fuel Injection
…
8.2 Removing and Installing
Distributor Drive Shaft
You will simplify the installation of the distributor drive shaft if you leave the engine in position to fire the No. 1 cylinder while the shaft is out.
To remove:
1. Remove the distributor. Take the spacer spring out of the recess in the top of the drive shaft.
2. Using an expansion tool or magnet, withdraw the distributor drive shaft. Then use a magnet to remove the two shim washers that are under the shaft on single-carburetor engines or the single spacer washer that is under the shaft on dual-carburetor engines.
CAUTION -
careful not to drop the washers into the timing gear chamber. Getting them out could require complete engine disassembly.
To Install:
1. Inspect the drive shaft for worn gear teeth and the washer(s) for scoring or wear. Their individual thickness should be 0.60 mm (.024 in.) for single carburetor engines or 1.30 mm (.051 in.) for dual carburetor and fuel injection engines. Have the engine in position to fire the No. 1 cylinder.
2. Coat the washer(s) with grease so that they will stick in place until the distributor drive shaft can be installed, then insert a stiff wire or rod in the engine.
Let the washers slide down the rod or wire and into position.
3. Insert the distributor drive shaft. It will turn slightly as it engages the crankshaft gear. Engage the teeth so that the shaft will be in the position shown previously in Fig. 8-2 or Fig. 8- 3 when fully installed.
4. Install the distributor. Check the ignition timing.
…