Complete workshop repair service manual with electrical wiring diagrams for New Holland TD5.65, TD5.75, TD5.80, TD5.85, TD5.90, TD5.95, TD5.100, TD5.105, TD5.100, TD5.115. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This New Holland TD5.65, TD5.75, TD5.80, TD5.85, TD5.90, TD5.95, TD5.100, TD5.105, TD5.100, TD5.115 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

“47445474.pdf”
New Holland TD5.65, TD5.75, TD5.85, TD5.95, TD5.105, TD5.115 Tractors Service Manual
1,207 pages PDF
Part number 47445474 English August 2013

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

“47454229.pdf”
New Holland TD5.65, TD5.75, TD5.80, TD5.90, TD5.100, TD5.110 Tractors Repair Manual
678 pages PDF
Part number 47454229 - 10-2012
…

EXCERPT:

Hydraulic systems - Hydraulic systems

Arm lowering phase

When the operator lowers the position control lever on his right, the return spring (4) pulls spool (1) to the right. Cylinder oil is exhausted under piston pressure (T) through lowering speed adjustment valve (17) and the port uncovered by spool.

Through spool port (F1) and draft sensitivity valve (12) oil flows to piston (9), which holds plunger (5) in the position shown, thus allowing pump delivery to be exhausted past plunger (5).

Unscrewing the screw (16) decreases the load on the spring (15), therefore the valve (14) can vibrate faster, slowing down the descent speed. Tightening the screw (16) slows down the vibration of the valve (14) that increases the descent speed of the arms since the valve (14) can remain in position in correspondence with the larger orifice where the oil fows out from the cylinder. After adjusting the arm descent speed it will not depend on the weight bearing on the arms but will be virtually constant.

Hydraulic systems - Component localization
…

47445474 - New Holland TD5.65, TD5.75, TD5.85, TD5.95, TD5.105, TD5.115 Tractors Service Manual....2
  Contents....4
  INTRODUCTION....7
  Engine....17
  Clutch....277
  Transmission....387
  Four-Wheel Drive (4WD) system....509
  Front axle system....519
  Rear axle system....597
  Power Take-Off (PTO)....641
  Brakes and controls....673
  Hydraulic systems....725
  Steering....805
  Wheels....857
  Cab climate control....871
  Electrical systems....933
  Platform, cab, bodywork, and decals....1149
  SPECIAL TOOL INDEX....1193
47454229 - New Holland TD5.65, TD5.75, TD5.80, TD5.90, TD5.100, TD5.110 Tractors Repair Manual....1209
  CONTENTS....1211
  GENERAL INSTRUCTIONS....1219
  SECTION 10 -- ENGINE....1225
  SECTION 18 -- CLUTCH....1343
  SECTION 21 -- TRANSMISSIONS....1379
  SECTION 23 -- DRIVE LINES....1425
  SECTION 25 -- FRONT AXLE MECHANICAL TRANSMISSION....1449
  SECTION 27 -- REAR AXLE AND TRANSMISSION....1489
  SECTION 31 -- POWER TAKE--OFF....1535
  SECTION 33 -- BRAKING SYSTEM....1559
  SECTION 35 -- HYDRAULIC SYSTEM....1585
  SECTION 41 -- STEERING....1651
  SECTION 44 -- FRONT AXLE AND WHEELS....1685
  SECTION 50 --AUXILIARY UNITS....1705
  SECTION 55 -- ELECTRICAL SYSTEM....1747
  SECTION 90 -- CAB....1863