Complete workshop & service manual with electrical wiring diagrams for New Holland E215B, E215BJ, E215BLC, E245B Crawler Excavator. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This New Holland E215B, E215BJ, E215BLC, E245B Crawler Excavator service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

“87677762A.pdf”
New Holland Kobelco E215B, E245B Crawler Excavator Worksop Manual
821 pages
Print No. 87677762A English - Edition - June 2007
…

— — — — — — — — — — — — — — — — — — — — —

“84163741.pdf”
New Holland Kobelco E215BJ Hydraulic Excavator (Hino Engine) Worksop Manual
795 pages
Book Code No. 84163741 English
…

— — — — — — — — — — — — — — — — — — — — —

“87731203.pdf”
New Holland Kobelco E215B, E215BLC (HS Engine) Hydraulic Excavator Worksop Manual
1,064 pages
Book Code No. 87731203 English
…

— — — — — — — — — — — — — — — — — — — — —

“87731205.pdf”
New Holland Kobelco E215B, E215BLC Hydraulic Excavator Worksop Manual
1,084 pages
Book Code No. 87731205 English
…

— — — — — — — — — — — — — — — — — — — — —

"87495894A - Crawler Excavators E215B Service Repair Manual.pdf"

— — — — — — — — — — — — — — — — — — — — —

"87739547 - Hydraulic Excavators E215B, E215BLC Shop Manual.pdf"

EXCERPT:

SWING DEVICE

Assembly

1. Sufficiently clean every part with wash oil and dry it with compressed air.

2. Check on every part for failure.

3. Attach oil seal (30) to sleeve (21) by means of special tool (xxxxxxxxx).

4. Insert sleeve (21) and oils seal (30) assy in pinion shaft (1).

5. Apply gear oil to the perimeter of axis of pinion shaft (1) lightly to prevent seizure.

6. Seal sufficient grease in spherical bearing (lower) (11) and force it in pinion shaft (1) by means of special tool (xxxxxxxxx).
Press force: 4~5 t
NOTE: since the bearing is formed with a partition at the center section, seal grease in it from both sides.

7. Apply sufficient grease to the pinion shaft assy. Grease: lithium extreme-pressure grease
(SHELL Albania EP2 or equivalent)

8. Place housing (13) on level bench and attach eye bolt to screw (M10) at the axis end of pinion shaft assy, and perpendicularly hang up pinion shaft assy and place it in the housing.
NOTE: horizontally orient the outer race of spherical bearing and insert it in by striking lightly. If the outer race is tilted, it is hard to insert even if striking.
Then do not force to insert it in, but take it away once and horizontally orient the outer race twice and insert it in again.

9. Set housing assy so that the pinion directs downward and fit oil seal (12) in housing (13) by means of special tool (xxxxxxxxx).
NOTE: apply Loctite #515 to the perimeter of oil seal. Fill one third (1/3) of the space of the grooveshaped section provided on the oil seal (12)
lip with grease. Insert it horizontally giving attention to the lip of oil seal so as not be damaged.
…