Complete workshop repair service manual with electrical wiring diagrams for Freightliner Cargo Van. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Freightliner Cargo service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

“STI-377, S14 (9_10P).pdf”
Freightliner Cargo Workshop Manual
STI-377, S14 (9/10P); 1,187 pages

Workshop Manual Contents
00 .......... General Information
01 .............. Engine
09 .............. Air Intake
13 ............ Air Compressor
15 ......... Alternators and Starters
20 ......... Engine Cooling / Radiator
25 .............. Clutch
26 ............ Transmission
30 ............ Throttle Control
31 ...... Frame and Frame Components
32 ............ Suspension
33 ............. Front Axle
35 ............. Rear Axle
40 ........... Wheels and Tires
41 .............. Driveline
42 .............. Brakes
46 .............. Steering
47 ............... Fuel
49 .............. Exhaust
54 ....... Electrical, Instruments, and Controls 60 ............... Cab
72 .............. Doors
82 ...... Windshield Wipers and Washer
83 ........ Heater and Air Conditioner
91 ....... Seatsand Restraint Systems
98 ............... Paint
…

— — —  — — —  — — —  — — —  — — —  — — —  — — —  — — —  — — —

“4_05P.pdf”
Freightliner Cargo Maintenance Manual

EXCERPT:
TRW TAS55/65 Power Steering Gear 46.01
Post-Service Checks
After power steering components have been worked on and before the vehicle is placed into service, the following items must be checked.
WARNING
Failure to check the following items could result in damage to the power steering system. This could cause a loss of hydraulic assist, which could cause personal injury or property damage.
1. Place a thermometer in the power steering reservoir, then warm the hydraulic system to normal operating temperature of 125 to 135°F (51 to 57°C) by operating the engine at low idle, while turning the steering wheel through several full left and right turns. With the engine running and the power steering system at operating temperature, turn the steering wheel slowly from stop to stop while checking the power steering reservoir for frothing or a change in the fluid level (a sign that air is trapped in the system). If air is present, inspect the system for leaking hoses or loose fittings.
Replace the hoses or tighten the fittings as necessary. Bleed the air from the system.
2. With the engine turned off and warm, check the power steering reservoir fluid level using the instructions in the steering section in the vehicle maintenance manual.
3. At full-left and full-right wheel cuts, be sure the axle stops (on the rear-side of the spindle) are set so there is at least 1/2 inch (13 mm) clearance between the tires and any fixed components that are attached to the vehicle. Clearance
between moving components should be 3/4 inch (19 mm). If clearance is less than the above, reset the axle stops.
4. Check that the poppet plungers are set correctly.
If needed, adjust them. For instructions refer to Subject 100
5. If there are still problems with the power steering system, see Section 46.04, Subject 300 and perform the troubleshooting procedures. Otherwise, go to the next step.
6. Test drive the vehicle, or take a ride with the driver. Check the steering wheel spoke position.
If during straight-ahead driving on a level road the steering wheel spokes are not within ±10 degrees of the 4 o’clock and 8 o’clock positions, remove the steering wheel and reposition it.
…
Freightliner Cargo Factory Service & Shop Manual