Complete workshop & service manual with electrical wiring diagrams for Perkins 4-Cylinder Series Engines (4.107, 4.108, 4.135, 4.154, 4.165, 4.182, 4.192, 4.203, D4.203, 4.2032, G4.204, 4.212, 4.236, G4.236, T4.236, 4.248, 4.2482, T4.38, 4.41, 4.99, 500 Series, Prima, Prima Marine). It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Perkins 4-Cylinder Series Engines service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST:
Workshop Manual for 200 Series Diesel Engines (4.135, 4.154, 4.182) (601SER01901176).pdf
Workshop Manual for 500 Series, Prima, Prima Marine Engines 4 Cylinder Diesel Engines for Vehicle, Marine, Agricultural & Industrial Applications (TPD01921273).pdf
Workshop Manual for 4.41 Series (Model LM) (4 Cylinder, Naturally Aspirated, Diesel Engine for Agricultural and Industrial Use) (TPD1322E3).pdf
Workshop Manual for 4.108, 4.107 & 4.99 Diesel Engines (601SER03811072).pdf
Workshop Manual for 4.154 Diesel Engines (601TPD01921024 supersedes 601TPD03831024).pdf
Workshop Manual for 4.165 Diesel Engines (601SER00801143).pdf
Workshop Manual for 4.192, 4.203 & D4.203 Diesel Engines (601SER06811010).pdf
Workshop Manual for 4.2032 Diesel Engines (TPD07911158).pdf
Workshop Manual for 4.2482, 4.248, T4.236, 4.236, 4.212 & T4.38 Diesel Engines (601TPD03931229).pdf
Workshop Manual for G4.204 Gasoline Engine.pdf
Workshop Manual for G4.236 Gasolene, Natural Gas, and LPG Engines (601TPD06841235).pdf
User's Handbook for 4.41 (Model LM) (4 Cylinder, Naturally Aspirated, Diesel Engine for Agricultural and Industrial Use) (TPD1319E5).pdf
User's Handbook for 4.108 Diesel Engine (201TPD03891218).pdf
User's Handbook for 4.165 Diesel Engine (SER1141).pdf
User's Handbook for 4.203 Series (D4.203, 4.2032) (201TPD10901216).pdf
User's Handbook for 4.236 Series (Models 4.236, T4.236, 4.248, 4.2482) (4 Cylinder Diesel Engines for Automotive, Agricultural and Industrial Use) (TPD1291E2).pdf
User's Handbook for 4.236 Series Spark Ignition Engines (G4.236 Gasolene, G4.236 LPG, and G4.236 Natural Gas Engines) (201TPD05841234).pdf
User's Handbook for G4.203 Diesel Engine (TPD1054).pdf
User’s Handbook for 200 Series Diesel Engines (TPD10941171).pdf
User's Handbook for 500 Series 4 Cylinder Diesel Engines for Industrial Use (TPD02951260EFG).pdf
User's Handbook for Prima Vehicle Engines (Model 80T) 4 Cylinder Turbocharged Diesel Engine for Vehicle Applications (TPD08931313E).pdf

EXCERPT:
Chapters
1 General information
2 Specifications
3 Cylinder head assembly
4 Piston and connecting rod assemblies
5 Crankshaft assembly
6 Timing case and drive assembly
7 Cylinder block assembly
8 Engine timing
9 Aspiration system
10 Lubrication system
11 Fuel system
12 Cooling system
13 Flywheel and housing
14 Electrical equipment
15 Auxiliary equipment
16 Special tools
…
"To remove and to fit the needle roller bearings for the drive shaft - Operation 5-18"
"1 Press out the bearings with a suitable adaptor."
"2 Clean the parent bores and lubricate them with clean engine lubricating oil."
"3 Make a suitable adaptor to the dimensions given in (A2). Fit the rear bearing (Operation 5-16/A7) onto the adaptor with the stamped face of the bearing towards the shoulder of the adaptor. Press the bearing into the parent bore in a continuous movement until the shoulder of the adaptor is against the front face of the balancer frame."
"In this position the front face of the bearing should be 130,0/131,0 mm (5.12/5.16 in) from the front face of the balancer frame, see Operation 5-16 (A)."
"4 Make a suitable adaptor to the dimensions given in (A1). Fit the front bearing (Operation 5-16/A10) onto the adaptor with the stamped face of the bearing toward the shoulder. Press the bearing into the parent bore in a continuous movement until the shoulder of the adaptor is against the front face of the balancer frame. In this position the front face of the bearing should be 2,5/3,0 mm (0.01/0.12 in) from the front face of the balancer frame, see Operation 5-16 (A)."
…