Complete workshop & service manual with electrical wiring diagrams for Hyundai Construction Wheel Loader HL760. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This service & repair manual Hyundai Construction Wheel Loader HL760, HL760-7, HL760-7A, HL760-9, HL760-9A, HL760-9AW, HL760-9S, HL760-9SB (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

EXCERPT:
CONTENTS
SECTION 1 GENERAL
Group 1 Safety Hints - - - - 1-1
Group 2 Specifications - - - 1-10
Group 3 Operational Checkout Record Sheet - - - 1-23
SECTION 2 ENGINE
Group 1 Structure and Function - - - - 2-1
Group 2 Engine speed and Stall rpm - - - 2-11
Group 3 Fuel Warmer System--------- - - - 2-12
SECTION 3 POWER TRAIN SYSTEM
Group 1 Structure and Function - - - - 3-1
Group 2 Operational Checks and Troubleshooting - - - 3-68
Group 3 Test and Adjustments - - - - 3-79
Group 4 Disassembly and Assembly - - - 3-81
SECTION 4 BRAKE SYSTEM
Group 1 Structure and Function - - - - 4-1
Group 2 Operational Checks and Troubleshooting - - - 4-29
Group 3 Tests and Adjustments - - - - 4-36
Group 4 Disassembly and assembly - - - - 4-38
SECTION 5 STEERING SYSTEM
Group 1 Structure and Function - - - - 5-1
Group 2 Operational Checks and Troubleshooting - - - 5-15
Group 3 Tests and Adjustments - - - - 5-23
Group 4 Disassembly and Assembly - - - 5-30
SECTION 6 WORK EQUIPMENT
Group 1 Structure and Function - - - - 6-1
Group 2 Operational Checks and Troubleshooting - - - 6-42
Group 3 Tests and Adjustments - - - - 6-53
Group 4 Disassembly and Assembly - - - 6-68
SECTION 7 ELECTRICAL SYSTEM
Group 1 Component Location - - - 7-1
Group 2 Electrical Circuit - - - 7-3
Group 3 Monitoring System - - - - 7-21
Group 4 Electrical Component Specification - - - 7-61
Group 5 Connectors - - - 7-68
Group 6 Troubleshooting - - - - 7-89
…
GENERAL PRECAUTIONS
Clean room with no dust is recommended for maintenance. Because hydraulic components are precision, and have minute clearance. Tool and wash-oil must be clean, too. Handle them carefully.
At removing control valve from the machine, wash around the piping port, and neither dust nor water should go into inside with plugging. It is same at attaching the machine.
Prepare the required parts by checking structure figure before assembly. There are parts which are supplied with only sub-assembly part, so check the parts list before assembly.
PRECAUTIONS FOR DISASSEMBLY
Handle the components carefully not to drop them or bump them with each other as they are made with precision.
Do not force the work by hitting or twisting as burred or damaged component may not be assembled or result in oil leakage or low performance.
When disassembled, tag the components for identification so that they can be reassembled correctly.
Once disassembled, O-ring and back-up rings are usually not to be used again.(Remove them using a wire with its end made like a shoe-horn. Be careful not to damage the slot)
If the components are left disassembled or half-disassembled, they may get rust from moisture or dust. If the work has to be interrupted, take care to prevent rust and dust.
PRECAUTIONS FOR REASSEMBLY
Take the same precautions as for disassembly.
When assembling the components, remove any metal chips or foreign objects and check them for any burrs or dents. Remove burrs and dents with oil-stone, if any.
O-rings and back-up rings are to be replaced with new ones, as a rule.
When installing O-rings and back-up rings, be careful not to damage them. (Apply a little amount of grease for smoothness)
Tighten the bolts and caps with specified torque.
…