Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Subaru Forester 1997-2017. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Subaru Forester 1997-2017 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

FILELIST: (4.1 G PDFs)
2003 FORESTER SERVICE MANUAL
2007 FORESTER SERVICE MANUAL
2015 FORESTER SERVICE MANUAL
2017 FORESTER SERVICE MANUAL
1998 FORESTER SERVICE MANUAL.pdf
1999 FORESTER SERVICE MANUAL.pdf
2000 FORESTER FACTORY SERVICE MANUAL.pdf
2000 FORESTER SERVICE MANUAL.pdf
2001 FORESTER FACTORY SERVICE MANUAL.pdf
2001 FORESTER SERVICE MANUAL.pdf
2002 FORESTER SERVICE MANUAL SUPPLEMENT.pdf
2002 FORESTER SERVICE MANUAL.pdf
2003 BODY REPAIR MANUAL.pdf
2003 FORESTER FACTORY SERVICE MANUAL.pdf
2003 FORESTER SERVICE MANUAL.pdf
2004 FORESTER FACTORY SERVICE MANUAL.pdf
2004 FORESTER SERVICE MANUAL.pdf
2005 FORESTER FACTORY SERVICE MANUAL.pdf
2005 FORESTER OFFICIAL SERVICE MANUAL.pdf
2005 FORESTER SERVICE MANUAL.pdf
2006 FORESTER SERVICE MANUAL.pdf
2007 FORESTER SERVICE MANUAL.pdf
2008 FORESTER SERVICE MANUAL.pdf
2009 BODY REPAIR MANUAL.pdf
2009 FORESTER SERVICE MANUAL.pdf
2010 FORESTER SERVICE MANUAL.pdf
2011 FORESTER SERVICE MANUAL.pdf
2012 FORESTER SERVICE MANUAL.pdf
2013 BODY REPAIR MANUAL.pdf
2013 FORESTER SERVICE MANUAL.pdf
2014 BODY REPAIR MANUAL.pdf
2014 FORESTER FACTORY SERVICE MANUAL.pdf
2014 FORESTER SERVICE MANUAL.pdf
2015 FORESTER SERVICE MANUAL.pdf

EXCERPT:
ENGINE 2 SECTION
FUEL INJECTION (FUEL SYSTEMS) FU(H4DOTC)
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)
EC(H4DOTC)
INTAKE (INDUCTION) IN(H4DOTC)
MECHANICAL ME(H4DOTC)
EXHAUST EX(H4DOTC)
COOLING CO(H4DOTC)
LUBRICATION LU(H4DOTC)
SPEED CONTROL SYSTEMS SP(H4DOTC)
IGNITION IG(H4DOTC)
STARTING/CHARGING SYSTEMS SC(H4DOTC)
ENGINE (DIAGNOSTICS)
EN(H4DOTC) (diag)
GENERAL DESCRIPTION GD(H4DOTC)
...
FUEL INJECTION (FUEL SYSTEMS) - General Description
C: CAUTION
• Prior to starting work, pay special attention to the following:
1. Always wear work clothes, a safety cap, protective shoes. Additionally, wear a helmet, protective goggles, etc. if necessary.
2. Protect the vehicle using a seat cover, fender cover, etc.
3. Prepare the service tools, clean cloth, containers to catch grease and oil, etc.
• Place “NO OPEN FLAMES” signs near the working area.
• Prepare a container and cloth to prevent scattering of fuels when performing work where fuels can be spilled. If the oil spills, wipe it off immediately to prevent from penetrating into floor or flowing out for environmental protection.
• Vehicle components are extremely hot immediately after driving. Be wary of receiving burns from heated parts.
• When performing a repair, identify the cause of trouble and avoid unnecessary removal, disassembly and replacement.
• Before disconnecting connectors of sensors or units, be sure to disconnect the ground cable from battery.
• Always use the jack-up point when the shop jacks or rigid racks are used to support the vehicle.
• Remove contamination including dirt and corrosion before removal, installation, disassembly or assembly.
• Keep the removed parts in order and protect them from dust and dirt.
• All removed parts, if to be reused, should be reinstalled in the original positions with attention to the correct directions, etc.
• Bolts, nuts and washers should be replaced with new parts as required.
• Follow all government and local regulations concerning disposal of refuse when disposing fuel.
• When the suspension-related components have been removed and installed, be sure to adjust the steering angle sensor.
D: PREPARATION TOOL
1. SPECIAL TOOL
...