Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Chevrolet Monte Carlo 1981-1988.1995-2008. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Chevrolet Monte Carlo 1981-1988.1995-2008 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
2007 ENGINE Engine Mechanical - 5.3L - Impala, Monte Carlo
Engine Flywheel Removal
Fig. 332: Identifying Flywheel
1. Remove the engine flex plate bolts.
2. Remove the flex plate.
IMPORTANT: The flex plate does not use a locating pin for alignment and will not
initially seat against the crankshaft flange, but will be pulled onto the crankshaft by the engine flex plate bolts. This procedure requires a 3 stage tightening process.
Oil Level Indicator and Tube Removal
Fig. 333: View Of Oil Level Indicator & Tube
1. Remove the oil level indicator (418) from the tube.
2. Remove the oil level indicator tube bolt (419).
3. Remove the oil level indicator tube (420).
IMPORTANT: Inspect the O-ring for cuts or damage. The O-ring may be used again if it
is not cut or damaged.
4. Remove the O-ring (421) from the tube, as required.
Exhaust Manifold Removal - Left Side
Fig. 334: Exhaust Manifold
1. Remove the spark plug wires from the spark plugs.
2. Remove the exhaust manifold, bolts, and gasket.
3. Discard the gasket.
Fig. 335: Heat Shield & Bolts
4. Remove the heat shield (603) and bolts (604) from the manifold (600), as required.
5. Remove the studs (605), as required.
Exhaust Manifold Removal - Right Side
Fig. 336: Exhaust Manifold
1. Remove the spark plug wires from the spark plugs.
2. Remove the exhaust manifold, bolts, and gasket.
3. Discard the gasket.
Fig. 337: Heat Shield & Bolts
4. Remove the heat shield (603) and bolts (604) from the manifold (600), as required.
5. Remove the studs (605), as required.
Water Pump Removal
Fig. 338: Engine Coolant Air Bleed Hose And Clamp
1. Disconnect the engine coolant air bleed hose and clamp (1).
Fig. 339: Water Pump, Bolts & Gasket
2. Remove the water pump (300), bolts (318), and gasket (314).
Fig. 340: Water Manifold, Bolts & Gaskets
3. Remove the water manifold (315), bolts (301), and gaskets (306).
Fig. 341: View Of Thermostat Housing, Bolts, Thermostat, & O-Ring
4. Remove the water inlet housing (303), bolts (302), thermostat (305), and O-ring (304), as required.
5. Discard the gaskets.
Throttle Body Removal
Fig. 342: Throttle Body Assembly
IMPORTANT: The intake manifold, throttle body, fuel injection rail, and fuel injectors may be removed as an assembly. If not servicing the individual components, remove the manifold as a complete assembly.
1. Remove the electrical wire harness connectors from the throttle body.
2. Remove the throttle body bolts (538).
3. Remove the throttle body (508).
4. Remove the throttle body gasket (509).
5. Discard the gasket.
...