Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Alfa Romeo 159 2005-2011. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Alfa Romeo 159 2005-2011 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

MAKE: Alfa Romeo
MODEL: 159 (1.8, 1.9 JTS, 2.2 JTS, 3.2 JTS, 1.9 JTD 8V, 1.9 JTD 16V, 2.4 JTD 20V)
YAER: 2005 2006 2007 2008 2009 2010 2011
LANGUAGE: EN/DE/ES/FR/IT/NL/PT

EXCERPT (Alfa Romeo 159 Service/Repair Manual):
Removing ( Refitting )
- Position the vehicle on a lift.
- Make sure that the ignition key is in the OFF position, then disconnect the battery terminal (-).
- Battery
See A001 BATTERY
Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM - DEHYDRATE AND REPRESSURIZE
Op. 7210A18 R.R FRONT CROSSMEMBER
- Using a suitable syringe, draw off the power assisted steering fluid from the reservoir.
Op. 4130B40 SUPPLY PIPE FROM PUMP TO POWER STEERING BOX - R.R.
1. Loosen the band and disconnect the supply pipe from the power assisted steering fluid reservoir to the pump, power assisted steering pump side.
2. Disconnect the rapid connector for the return pipe from the heat exchanger pipe to the power assisted steering fluid reservoir, heat exchanger side.
3. Undo the bolts (3a) and remove the power assisted steering fluid reservoir (3b) complete with pipes (3c).
4. Loosen the band and disconnect the coolant return pipe, cylinder head side.
1. Disconnect the rapid connector for the power assisted steering system heat exchanger inlet pipe, heat exchanger side.
2. Remove the heat exchanger pipe (2a) after having released it from the securing band (2b).
1. Undo the bolt (1a) and disconnect the inlet/outlet pipes from the air conditioning compressor (1b).
Seal the connectors that have been disconnected using suitable plugs to prevent dampness and impurities from entering the system.
2. Undo the nut (2a) and disconnect the air conditioning pipes intermediate flange (2b).
Seal the connectors that have been disconnected using suitable plugs to prevent dampness and impurities from entering the system.
3. Remove the air conditioning system pipes.
Op. 5530B10 BATTERY - R+R
1. Disconnect the electrical connections from the injection/ignition system control unit.
1. Engine management control unit
See M010 ENGINE MANAGEMENT ECU
2. Undo the bolts (2a) and remove the battery drip tray (2b) complete with injection/ignition system control unit (2c).
1. Open the junction unit cover, rotate the junction unit and disconnect the electrical connection (connector A).
Front/engine coupling
See D004 FRONT/ENGINE COUPLING
1. Loosen the band and disconnect the brake servo vacuum intake pipe, air chamber side.
1. Disconnect the rapid connector for the fuel vapor pipe intermediate coupling.
2. Disconnect the rapid connector for the fuel supply pipe, multiple connector side.
- Discharge the fuel supply system pressure.
1. Disconnect the electrical connection for the left upper Lambda sensor. Lambda sensor on pre-catalyzer
See K015 LAMBDA SENSOR ON PRE-CATALYZER
2. Disconnect the electrical connection for the right upper Lambda sensor. Lambda sensor on pre-catalyzer -2
See K016 LAMBDA SENSOR ON PRE-CATALYZER -2
3. Disconnect the electrical connection for the left rear Lambda sensor to the catalytic converter. Lambda sensor on catalyzer
See K017 LAMBDA SENSOR ON CATALYZER
4. Disconnect the electrical connection for the right rear Lambda sensor to the catalytic converter. Lambda sensor on catalyzer 2
See K018 LAMBDA SENSOR ON CATALYZER - 2
Mark the electrical connections for disconnect them so that they can be correctly refitted.
1. Disconnect the rapid connectors for the air conditioning system heater coolant inlet and outlet pipes.
1. Loosen the collar and disconnect the supply pipe from the engine coolant reservoir.
- Replace the brake-clutch fluid reservoir plug using the tool
Brake-clutch fluid reservoir cap
1. Release the retaining clip (1a) and disconnect the pipe (1b) between the damper and the clutch operating cylinder (1b), operating cylinder side.
2. Undo the bolt (2a) and disconnect the earth lead (2b) (connector B) from the gearbox.
Battery earth on engine
See C002 BATTERY EARTH ON ENGINE
1. Disconnect the electrical connection from the reversing light switch
Reversing lights switch
See I020 REVERSING LIGHTS SWITCH
1. Disconnect the gear selector cable.
2. Disconnect the gear engagement cable.
1. Unscrew the bolts (1a) and move aside the bracket (1b) complete with gear selection and engagement cables (1c).
Op. 4450B12 FRONT WHEELS (TWO) - R+R
Op. 1076B72 INTERMEDIATE EXHAUST PIPE WITH HOSE SECTION - R+R
1. Undo the bolts (1a) and move the brake caliper assemblies (1b) to the side and secure them appropriately.
1. Undo the nuts fixing the steering rods to the front steering knuckles.
2. Disconnect the steering rods (2a) from the front steering knuckle using the tool (2b).
Extracting steering rod from steering knuckle
1. Undo the nuts (1a) and disconnect the front suspension upper track control arms (1b) from the steering knuckles (1c).
...