Complete workshop & service manual with electrical wiring diagrams for Komatsu Hydraulic Excavator PC600-6, PC600LC-6, PC600-7, PC600LC-7, PC600-8, PC600-8E0, PC600LC-8E0, PC600LC-8, PC650-1, PC650-3, PC650LC-3, PC650SE-3, PC650-5, PC650-8E0, PC650LC-8E0, PC700LC-8E0, PC710-5. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Komatsu Hydraulic Excavator PC600-6, PC600LC-6, PC600-7, PC600LC-7, PC600-8, PC600-8E0, PC600LC-8E0, PC600LC-8, PC650-1, PC650-3, PC650LC-3, PC650SE-3, PC650-5, PC650-8E0, PC650LC-8E0, PC700LC-8E0, PC710-5 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST:
GEN00013-01 - Hydraulic Excavator PC600-7 Field Assembly Instruction.pdf
GEN00043-04 - Hydraulic Excavator PC600-8, PC600LC-8 Field Assembly Instruction.pdf
GEN00101-02 - Hydraulic Excavator PC600-8E0, PC600LC-8E0, PC650-8E0, PC650LC-8E0, PC700LC-8E0 Field Assembly Instruction.pdf
SEAM000604 - Hydraulic Excavator PC650-5, PC650LC-5, PC650SE-5, PC710-5, PC710SE-5 Operation & Maintenance Manual.pdf
SEAM022100 - Hydraulic Excavator PC600-6, PC600LC-6 avance Operation & Maintenance Manual.pdf
SEAM022108T - Hydraulic Excavator PC600-6, PC600LC-6 Operation & Maintenance Manual.pdf
SEAM046200 - Hydraulic Excavator PC600-6, PC600LC-6 avance Operation & Maintenance Manual.pdf
SEAM053202T - Hydraulic Excavator GALEO PC600-7, PC600LC-7 Operation & Maintenance Manual.pdf
SEAM02090303 - Hydraulic Excavator PC650-3 Operation & Maintenance Manual.pdf
SEAM02090306 - Hydraulic Excavator PC650-3, PC650LC-3, PC650SE-3 Operation & Maintenance Manual.pdf
SEAW001700 - Hydraulic Excavator PC600-6 Field Assembly Instruction.pdf
SEAW002802 - Hydraulic Excavator PC600-6, PC600LC-6 Field Assembly Manual.pdf
SEAW004900 - Hydraulic Excavator (Loading Shovel) PC600-6, PC600LC-6 Field Assembly Manual.pdf
SEBM0209A04 - Hydraulic Excavator PC650-1 Shop Manual.pdf
SEBM000607 - Hydraulic Excavator PC650-5, PC710-5 Shop Manual.pdf
SEBM017111 - Hydraulic Excavator PC600-6, PC600LC-6 Shop Manual.pdf
SEBM027100K - Hydraulic Excavator PC600LC-6 Shop Manual Supplement for Machines Built To Cold Weather Specifications (-50°C) (use with SEBM017100 & revisions).pdf
SEBM031206 - Hydraulic Excavator PC600-7, PC600LC-7 Shop Manual.pdf
SEBM02090307 - Hydraulic Excavator PC650-3, PC650LC-3, PC650SE-3 Shop Manual.pdf
SEN00128-16 - Hydraulic Excavator PC600-8, PC600LC-8 Shop Manual.pdf
SEN05377-03 - Hydraulic Excavator PC600-8E0, PC600LC-8E0, PC650-8E0, PC650LC-8E0, PC700LC-8E0 Shop Manual.pdf
TEN00037-02 - Hydraulic Excavator PC600-7, PC600LC-7 Operation & Maintenance Manual.pdf
TEN00118-07 - Hydraulic Excavator PC600-8, PC600LC-8 Operation & Maintenance Manual.pdf
TEN00346-02 - Hydraulic Excavator PC600-8, PC600LC-8 Operation & Maintenance Manual.pdf
TEN00405-03 - Hydraulic Excavator PC600-8E0, PC600LC-8E0, PC650-8E0, PC650LC-8E0, PC700LC-8E0 Operation & Maintenance Manual.pdf
UEAM005000 - Hydraulic Excavator PC600-8, PC600LC-8 Operation & Maintenance Manual.pdf

EXCERPT:
50 Disassembly and assembly SEN01065-03
Removal and installation of swing motor and swing machinery
assembly
Removal
Lower the work equipment to the ground and stop the engine.
Loosen the cap of the hydraulic tank gradually to release the internal pressure of the hydraulic tank.
1. Remove step (1).
2. Disconnect 4 hoses (2) between the control valve and swing motor.
a Install tags and oil stopper plugs to all the disconnected hoses.
3. Disconnect 2 suction hoses (3).
4. Disconnect 2 swing holding brake hoses (4).
5. Disconnect 3 drain hoses (5).
6. Remove hose bracket (6).
7. Disconnect drain plug assembly (8) from the chassis at the rear of swing motor and swing machinery assembly (7).
8. Remove mounting bolts (9) and lift off swing motor and swing machinery assembly (7). [*1]
4 Swing motor and swing machinery assembly: 440 kg (1 piece)
Installation
Carry out installation in the reverse order to removal.
[*1]3 Swing motor and swing machinery assembly mounting bolt:
824 – 1,030 Nm {84 – 105 kg}
Refilling with oil (Hydraulic tank)
Add oil through the oil filler to the specified level. Run the engine to circulate the oil through the system. Then, check the oil level again.
Bleeding air
Bleed air from the swing motor. For details, see Testing and adjusting, "Bleeding air from each part".
…
ASSEMBLY OF FINAL DRIVE ASSEMBLY
* Clean all parts, and check for dirt or damage. Coat the sliding surfaces of all parts with engine oil before installing.
1. Shaft assembly
1) Using tool C1, install floating seal (33) to shaft (34).
* Remove all grease and oil from the O-ring and O-ring contact surface of the floating seal, and dry before installing.
* After installing the floating seal, coat the sliding surface thinly with engine oil.
2) Install bearing (31 ).
2. Hub assembly
1) Assembly of hub assembly
i) Using tool Cs, press fit outer race (35) to hub (30).
ii) Using tool C1, install floating seal (33) to hub (30).
* For details of the installation procedure, see Step 1-1).
2) Using eyebolts I , install hub assembly (30) to shaft assembly (34).
...