Complete workshop & service manual with electrical wiring diagrams for SkiDoo REV, REV-XP/XR2, REV-XR 1200 Series 2005-2010. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This SkiDoo REV, REV-XP/XR2, REV-XR 1200 Series 2005-2010 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

“'05 REV.pdf”
MAKE: Ski-Doo
YEARL: 2005
MODEL: REV Series (EXPEDITION, GSX, GTX, MX Z, MX-Z (Adrenaline), SUMMIT), RT Series (MACH Z, SUMMIT HIGHMARK, SUMMIT HIGHMARK X), TUNDRA, SKANDIC LT/LT E/WT/SWT/WT LC/SUV 550/SUV 600, EXPEDITION TUV 600 HO SDI/TUV V-1000
PAGE: 1,429

MAKE: Ski-Doo
YEARL: 2006
MODEL: REV Series (EXPEDITION, GSX, GTX, MX Z, MX-Z (Adrenaline), SUMMIT)
PAGE: 502

“REV-XP/XR2, REV-XR 1200 4-TEC '09-'10.pdf”
MAKE: Ski-Doo
YEARL: 2009 2010
MODEL: REV-XP/XR (2-stroke) Series (GTX LE 600 HO E-TEC, GSX Limited 600 HO E-TEC, GSX Sport 500SS, GTX Sport 500SS, MXZ 50TH 600 HO E-TEC, MXZ Adrenaline 800R Power TEK, MXZ Renegade 600 HO E-TEC, MXZ Renegade 800R Power TEK, MXZ Renegade X 600 HO E-TEC, MXZ Renegade X800R Powder TEK, MXZ Trail 500SS, MXZ TNT 500SS, MXZ TNT 600 HO E-TEC, MXZ X 600 HO E-TEC, MXZ X 800R Powder TEK, Summit 50TH 800R Powder TEK, Summit Everest 600, Summit Everest 600 HO E-TEC, Summit Everest (146) 800R Powder TEK, Summit Everest (154) 800R Powder TEK, Summit Everest (163) 800R Powder TEK, Summit Hill Climb (154) 800R Powder TEK, Summit X 600 HO E-TEC, Summit X (146) 800R Powder TEK, Summit X (154) 800R Powder TEK, Summit X (163) 800R Powder TEK); REV-XR 1200 Series (GTX LE, GTX SE, GSX Limited, MXZ Renegade, MXZ Renegade X, MXZ TNT, MXZ X)
PAGE: 1,230

EXCERPT:
Section 03 ENGINES
Subsection 08 (COOLING SYSTEM)
DISASSEMBLY AND ASSEMBLY Coolant Pump
Refer to BOTTOM END section.
Sender and Plug
Apply Loctite 592 (P/N 293 800 018) thread sealant on sender no. 3 and plug no. 4 to avoid leaks.
Pressure Cap
Check if the cap no. 1 pressurizes the system for 3minutes. If not,install a new 90k Pa (13PSI) cap (do not exceed this pressure).
Coolant Tank
For removal, drain cooling system before removing coolant tank no. 2.
Remove all hoses from coolant tank.
Remove injection oil reservoir retaining screws to slide down the coolant tank to disengage it from oil tank.
NOTE: It is necessary to move oil tank for an easier removal/installation of coolant tank.
Check if the tank is cracked or melted. Replace if necessary.
For installation, reverse the removal procedure.
Front Radiator
Remove all debris between radiator fins. A clean radiator is more efficient than a dirty one.
Check if the radiator fins are damaged. Replace the front radiator no. 13 if necessary.
NOTE: A radiator with many broken fins does not work properly.
For disassembly, drain cooling system.
Remove rear suspension (refer to REAR SUSPEN- SION).
Using Supertanium bit (P/N 529 031 800), drill all rivets no. 14 retaining front radiator to the frame or grind the rivets with a grinding disk.
Pull the radiator a little and remove the Oetiker clamps no. 10.
For installation, reverse the removal procedure.
…