Complete workshop & service manual with electrical wiring diagrams for Porsche 914/924/944/951/968 1969-1995. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Porsche 914/924/944/951/968 1969-1995 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

FILELIST: (1.2 G PDFs)
914 (USA) Classic
914-4 & 914-6 ('69-'76)
924 (Turbo) 1976-1985 Workshop Manual.pdf
944 1982-1991 Workshop Manual.Model application.txt
944 1982-1991 Workshop Manual.pdf
944-951 1982-1991 Workshop Manual.pdf
968 1992-1995 Workshop Manual.pdf
bonus_material
Technical Bulletins
1968-1988 Porsche All Models Emission Equipment & Tune-up Specifications.pdf
1986-1988 Porsche 924S, 1984-1989 944 Dimensions Tolerances.pdf
1987-1988 Porsche 944S, 1989-1991 944S2, 1985-1991 944 Technical Specifications.pdf
1992-1993 Porsche 968, 1993 968 CS Technical Specifications.pdf
Bosche DME Schematic-Analog.pdf
Bosche DME Schematic-Digital.pdf
DME Testing 83 944.pdf
DME Testing 85+ 944.pdf
Mechanical Fuel Injestion Manual.pdf
Porsche 944 Drivers Manual.pdf
Porsche 968 History.pdf
Porsche Special Tools.pdf
Procedure for Inspection of Porsche 968 Camshafts.pdf
Transmission Automatic A22 Valve Body.pdf

EXCERPT:
TABLE OF CONTENTS
General
Technical data . . . . . 0.1
Maintenance, Self-diagnosis general
Maintenance
Operating instructions for system tester
Engine, Crankcase, Engine Mounts
Tolerances and wear limits . . . . . . . . . . . . . . . . . 10-1
Tightening torques for engine . . . . . . . . 10-5
Removing and installing engine (manual transmission) . . . . . . . 10-9
Removing and installing engine (Tiptronic transmission) . . . . . . 10-13
Engine, Crankshaft, Pistons
Adjusting guide rail for balance shaft toothed belt
Checking adjustment of balance shafts . . . . . . 13-3
Fitting toothed belt for balance shaft . . . . . 13-5
Adjusting Special Tool9201 . . . . . . . . . 13-7
Checking and adjusting balance shaft toothed belt tension . . . . 13-9
Crankcase markings . . . . 13 -13
Locking the flywheel for assembly work . . . . . . 13 -15
Enginesupport . . . . . . . . . . . . . . . 13-17
Crankcase-Tools. . . . . . 13-19
Machining cylinder bores in upper crankcase section . . . . . . . 13-21
Crankcase -Installation length or protrusion length of studs . . . . 13-24c
Dismantling and assembling crankcase, crankshaft . . . . . . . . 13-25
Aligning the upper and lower parts of the crankcase . . . . . . . . 13-29
Crankshaft-Standard and Repair Dimensions . . . . . . . . . . . 13-31
Dismantling and assembling pistons, connecting rod . . . . . . . 13-33
Checking piston and cylinder bore . . . . . . 13 -37
Dismantling and assembling balance shaft drive . . . . . . . . . . 13 -39
Removing and installing double-mass flywheel and grooved ball bearing . . . . . . . . . 13-43
Engine, Cylinder Head, Valve Drive
Replacing the camshaft toothed belt (with hydraulic belt tensioner) . . . .15-1
Adjusting and checking the camshaft setting . . . .15-3
Applying TDC mark to camshaft sprocket . . . . . 15-7
Camshaft adjustment gauge (shop-made). . . . . 15-9
Fitting the camshafts . . . . 15 -11
Fitting the camshaft seal . . . . . . . . . . . 15 -15
Camshaft references . . . . . . . . . 15-17
Machining the cylinder head mating face . . . . . . . . . . . 15-19
Removing and installing cylinder head . . . . . . . . . . 15-21
Valve dimensions . . . . . . . . . . . . . 15-24a
Dismantling and assembling camshaft drive . . . . 15 -25
The following topics of Repair group 15 are described In the
Repair Manual Type 944, vol. 1 • A:
Cylinder head, disassembling and assembling . . . . . 15-115
Valve springs, removing and installing with Sauer tool . . . . 15-118
Valve springs, removing and installing, removing valve stem seal . . . . . . 15-121
Checking valve guides . . . . 15 -123
Replacing valve guides . . . . 15 -125
Checking valve-seat wear limit . . . . . . . . 15 -130
Valve seats, checking and machining . . . . . . . . . . . . . . 15-131
Checking and adjusting installation length of valve springs . . . . . 15 -133
Engine, Lubrication
Removing and installing lubrication system components . . . . . . 17 -1
Dismantling and assembling oil pressure release valve . . . . . . . 17-5
Removing and installing oil restraining valve . . . . 17 -7
Checking oil pressure . . . . . . . . . . . . . 17-9
Cleaning the entire engine oil system . . . . . . . . . . . . . . . . 17-11
Engine, Cooling
Mixing table
Checking cooling and heating system for tightness . . . . . . . . . 19-
Fuel Supply
Fuel vacuum line routing . .
The following topics of Repair group 20 are described In the
Repair Manual Type 944, vol. 1
Replacing fuel filter, checking injection lines for leaks and tightness . . 20-102
Fuel System - Electronic Injection
Test values
Checking idle and CO level of vehicles without catalytic converter . . . . . . . . . . . . 24 -2
Checking idle and CO level of vehicles with catalytic converter . . . . . . . . . . 24 -3
Removing and installing DME injection system components. . . . 24-5
Removing and installing injection valves . . . . . . 24 -9
The following topics of Repair group 24 are described In the
Repair Manual Type 944, vol. 1
Checking fuel pressure
Ignition system
Replacing spark plugs . . . .28 -1
DME control units as of Model Year '92 . . . . . . 28 -3
Removing and installing knock sensors . . . . . . 28 -5
DME-Diagnosis I Troubleshooting . . . . . . 024/28 -1
...