Complete workshop & service manual with electrical wiring diagrams for Fendt Tractor 300-series (309/310/311/312) Vario COM III. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Fendt Tractor 300-series (309/310/311/312) Vario COM III service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

X990.005.056.010 - Fendt Tractor 300-series (309/310/311/312) Vario COM III Workshop Manual.pdf
0000 Tractor / General system
1000 Transmission
1005 Transmission control unit
1010 Differential
1015 Axle drive
1030 Handbrake
1050 Housing
1070 Brake system
1080 Vario transmission unit
1090 Emergency control
1100 Clutch actuation system
1150 Cardan brake
1170 ML range control
1200 Front PTO
1220 Live PTO
1320 Front-wheel drive
1430 Hydrodamp
1432 Hydraulic pump
1470 Transmission lubrication system
1490 Pump drive
1530 ML adjustment
1600 Enhanced control system valves
1620 Enhanced control system pipes
2000 Engine
2010 Cylinder head
2020 Speed adjustment
2050 Cooling system
2060 Fuel system
2170 Engine brake
2180 Cold-start system
2190 Intercooler
2210 Crankcase
2250 Engine preheater
2312 Lubrication
2710 Injection pump
2712 Injectors
2714 Governor
3000 Front axle
3010 Front axle support
3020 Axle housing
3050 Suspension
3060 Suspension valve fitting
3070 Suspension pipe
3100 Track rod
3120 Steering cylinder
3170 Frame
3180 Cardan shaft
3190 Diff. lock actuation system
4000 Steering
4070 Steering wheel
4090 Hydraulic steering assembly
5000 Vehicle body
5010 Design
5030 Driver seat
5050 Trailer hitch
5161 Trailer hitch coupling
5200 Cab mount, suspension
5500 Air conditioning system
5520 Compressor drive
5530 Coolant lines
5550 Evaporator
5560 Condenser
5570 Electrical cables
8100 Cab
8113 Heater
8114 Ventilation
8117 Windscreen wipers
8121 Cable loom
8600 Power lift
8610 Electrohydraulic EPC control
8618 External control
8631 Control lifting gear
8700 Three-point hitch
8730 Lift arms
8740 Support
8800 Compressed air system
8810 Compressor
8820 Brake fittings
8830 Lines
8850 Electrical actuation system
8890 Air tank
8900 Front loader
8910 Mounting frame
8915 Hydraulic implement actuation system
8955 3. hydraulic circuit
8958 Multi-coupling
8970 Pipes
8990 Lift cylinder
9000 Electrics
9010 Alternator
9015 Starter lockout
9040 Fuses
9050 Battery system
9060 Starter motor system
9200 Front power lift
9210 Lift gear
9211 External control
9220 Cylinder
9230 Pipes
9260 Enhanced control power lift
9280 Frame
9400 Hydraulic pump assembly
9410 LS pump
9420 Transmission pump
9430 Steering pump
9500 Hydraulic pipes
9510 Base circle
9516 Power lift
9525 with oil cooler
9530 Hydraulic trailer brake
9531 Steering
9534 Reversing system
9600 Hydraulic equipment
9605 Hydraulic connections
9610 Central control block (ZSB)
9620 Valve assembly
9666 External pressure supply
9690 Valve supplement
9700 Electronics
9710 Instrument panel
9715 Terminal
9717 LBS - agricultural bus system
9720 Transducer
9730 Radar sensor
9740 E-box
9750 Transmission actuator unit
9760 Drive switch
9770 Control panel
9780 Engine EDC
9790 ECU, lift gear
9900 Service
9920 Special tools
9970 FENDIAS

EXCERPT:
Adjustment instructions for wiper blade
A = Wiper width
B = Wiping angle
C = Adapter screw in bore of wiper arm
E = Observe distance
D = Parking position
Pull forward separation point (X258) behind roof lining, guide through grommet in cab roof and connect to wiper motor (M004).
Fasten surplus separation point (arrowed) using cable tie.
...