Complete Operator's Manual for John Deere 50C ZTS Excavator, with all the workshop information to maintain & operate JD 50C ZTS Excavator.

OMT190903 - John Deere 50C ZTS Excavator Operator's Manual.pdf
omt190904 - John Deere Excavateur 50C ZTS.pdf
omt190905 - John Deere Excavadora 50C ZTS.pdf

Total Pages: 295 pages
File Format: PDF (Internal Links, Bookmarked, Table of Contents, Searchable, Printable, high quality)
Category: Operator's Manual
Language: English Spanish French
Published on 2007/08/24

Table of Contents
Introduction
Emissions Control Warranty Statement
Technical Information Feedback Form
Section 1-1: Safety-Safety Features
Safety Features
Section 1-2: Safety-General Precautions
Recognize Safety Information
Follow Safety Instructions
Operate Only If Qualified
Wear Protective Equipment
Avoid Unauthorized Machine Modifications
Add Cab Guarding For Special Uses
Inspect Machine
Stay Clear Of Moving Parts
Avoid High-Pressure Fluids
Beware Of Exhaust Fumes
Prevent Fires
Prevent Battery Explosions
Handle Chemical Products Safely
Dispose Of Waste Properly
Prepare For Emergencies
Section 1-3: Safety-Operating Precautions
Use Steps And Handholds Correctly
Start Only From Operator's Seat
Use And Maintain Seat Belt
Prevent Unintended Machine Movement
Avoid Work Site Hazards
Keep Riders Off Machine
Avoid Backover Accidents
Avoid Machine Tip Over
Use Special Care When Lifting Objects
Add And Operate Attachments Safely
Section 1-4: Safety-Maintenance Precautions
Park And Prepare For Service Safely
Service Cooling System Safely
Remove Paint Before Welding or Heating
Make Welding Repairs Safely
Drive Metal Pins Safely
Section 1-5: Safety-Safety Signs
Safety Signs
Section 2-1: Operation-Operator's Station
Pedals And Levers
Monitor Panel
Monitor Panel Functions
Horn Switch
Engine Speed Control Lever
Pilot Control Shut-Off Lever
Windshield Washer And Wiper Switch
Travel Alarm And Travel Alarm Cancel Switch
Cab Heater-If Equipped
Cab Door Release Lever
Secondary Exit Tool
Opening Front (Secondary Exit) Window
Closing Front Window
Opening Rear Window
Opening Right Side Window
Adjusting Operator Seat
Tool Box And Operator’s Manual Compartment
Section 2-2: Operation-Operating The Machine
Before Starting Work
Operator's Daily Machine Check Before Starting
Starting The Engine
Starting The Engine In Cold Weather
Check Instruments After Starting
Using Booster Batteries-12 Volt System
Cold Weather Warm-Up
Travel Pedals And Levers
Fast Speed Travel Pedal
Control Lever Pattern Operation
Control Lever Pattern Conversion
Boom-Swing Pedal
Optional Pedal
Positioning Auxiliary Line Selector Valve
Operating Backfill Blade
Operating Tips-Backfill Blade
Operating In Water And Mud
Select Correct Track Shoes
Driving Up A Steep Or Slippery Slope
Lifting
Lower Boom With Engine Stopped
Parking
Loading And Unloading For Transport
Transporting Machine With Rubber Tracks
Towing Machine A Short Distance
Lifting Machine
Section 3-1: Maintenance-Machine
Diesel Fuel
Bio-Diesel Fuel
Low Sulfur Diesel Fuel Conditioner
Dieselscan Fuel Analysis
Handling And Storing Diesel Fuel
Alternative And Synthetic Lubricants
Engine Break-In Oil
Diesel Engine Oil
Hydraulic Oil
Propel Gearbox Oil
Track Adjuster, Working Tool Pivot, Swing Bearing, And Swing Bearing Gear Grease
Section 3-2: Maintenance-Periodic Maintenance
Service Your Machine At Specified Intervals
Check The Hour Meter Regularly
Prepare Machine For Maintenance
Open Hood And Access Cover
Fuel Tank
Hydraulic Breaker And Crusher Attachments
Maintenance And Repair Record Keeping System
OILSCAN Plus OILSCAN Plus is a registered trademark of Deere & Company , CoolScan Plus CoolScan Plus is a registered trademark of Deere & Company , And 3-Way Coolant Test Kit
Periodic Maintenance Record Keeping System
Section 3-3: Maintenance-As Required
Clean Radiator Core
Clean Air Cleaner Element
Section 3-4: Maintenance-Every 10 Hours or Daily
Check Engine Oil Level
Check Hydraulic Oil Tank Level
Drain Fuel Tank Sump
Drain Water Separator
Check Recovery Tank Coolant Level
Check Bucket Teeth
Check Track Sag-Rubber Track
Check Track Sag-Steel Track, If Equipped
Adjusting Track Sag
Rubber Track Care
Removing Rubber Track
Installing Rubber Track
Converting The Track
Seat Belt
Section 3-5: Maintenance-Every 50 Hours
Inspect Fan Belt, Check And Adjust Tension
Change Engine Break-in Oil And Replace Filter
Section 3-6: Maintenance-Every 100 Hours
Grease Bucket And Link Pins
Section 3-7: Maintenance-Every 250 Hours
Grease Swing Bearing
Check Propel Gearbox Oil Level
Drain Hydraulic Oil Tank Sump
Replace Hydraulic Oil Tank Filter
Section 3-8: Maintenance-Every 500 Hours
Change Engine Oil And Replace Filter
Grease Front Joint Pins
Grease Swing Bearing Gear
Grease Control Lever Universal Joint
Replace Final Fuel Filter
Replace Air Cleaner Element
Drain Cooling System
Diesel Engine Coolant
Cooling System Fill And Deaeration
Section 3-9: Maintenance-Every 1000 Hours
Change Propel Gearbox Oil
Replace Pilot System Oil Filter
Check And Adjust Engine Valve Lash (Clearance)
Check Starter And Alternator
Section 3-10: Maintenance-Every 2000 Hours
Change Hydraulic Tank Oil, Clean Suction Screen
Section 4-1: Miscellaneous-Machine
Do Not Service Or Adjust Injection Nozzles Or Injection Pump
Do Not Service Control Valves, Cylinders, Pumps Or Motors
Precautions For Alternator And Regulator
Handling, Checking And Servicing Batteries Carefully
Using Battery Charger
Replacing Batteries
Welding On Machine
Clean Machine Regularly
Electrical Socket
Replacing Fuses
Installing Bucket With Quick Coupler
Track Sag General Information
Check Track Shoe Hardware
Unified Inch Bolt And Cap Screw Torque Values
Metric Bolt And Cap Screw Torque Values
Section 4-2: Miscellaneous-Operational Checkout
Operational Checkout
Section 4-3: Miscellaneous-Troubleshooting
Using Troubleshooting Charts
Engine
Electrical System
Hydraulic System
Section 4-4: Miscellaneous-Storage
Prepare Machine For Storage
Section 4-5: Miscellaneous-Serial Numbers
Record Product Identification Number (PIN)
Record Engine Serial Number
Keep Proof of Ownership
Keep Machines Secure
Section 4-6: Miscellaneous-Specifications
Engine Specifications
Drain And Refill Capacities
Machine Specifications
Working Ranges
Lift Capacity-KG (LB)(Blade Off The Ground With Standard Boom And Rubber Track)
Lift Capacity-KG (LB)(Blade On The Ground With Standard Boom And Rubber Track)

John Deere 50C ZTS Excavator Operator's Manual (OMT190903)