Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Komatsu Bulldozer D375A-2, D375A-3, D375A-5, D375A-5E0, D375A-6, D375A-6R. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your bulldozer like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Komatsu Bulldozer D375A-2, D375A-3, D375A-5, D375A-5E0, D375A-6, D375A-6R is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

1.20 GB PDF

GEN00054-04 - Bulldozer D375A-5E0 Field Assembly Instruction (SN50001&up).pdf
GEN00097-03 - Bulldozer D375A-6 Field Assembly Instruction (SN60001&up).pdf
GEN00099-03 - Bulldozer D375A-6 Field Assembly Instruction (SN60001&up).pdf
SEAD010801 - Bulldozer D375A-3 Operation & Maintenance Manual (SN17001&up).pdf
SEAD048900 - Bulldozer D375A-5 (Radio Control Special Small Electric Power Specification) Operation & Maintenance Manual.pdf
SEAM008300 - Bulldozer D375A-2 Operation & Maintenance Manual (SN16305&up).pdf
SEAM022602T - Bulldozer D375A-3 Operation & Maintenance Manual (SN17501&up).pdf
SEAM045600T - Bulldozer D375A-3 Operation & Maintenance Manual (SN17736&up).pdf
SEAWD03103 - Bulldozer GALEO D375A-5E0 Field Assembly Instruction (SN18001&up).pdf
SEBD016104 - D375A-3 Shop Manual (SN17501&up).pdf
SEBD028900 - D375A-5 (Radio-Control Specification) Shop Manual.pdf
SEBM008403 - D375A-3 Shop Manual (SN17001&up).pdf
SEBM023508 - D375A-5 Shop Manual (SN18001&up).pdf
SEBM026600 - D375A-3 Shop Manual (SN17736&up).pdf
SEBM035200 - D375A-5 Shop Manual (SN18200&up).pdf
SEBM036103 - D375A-5 (VHMS Specification) Shop Manual (SN18052&up).pdf
SEBM01970207 - D375A-2 Shop Manual (SN16001&up).pdf
SEN00986-11 - Bulldozer D375A-5E0 Shop Manual (SN50001&up).pdf
SEN05006-09 - Bulldozer D375A-6 Shop Manual (SN60001&up).pdf
SEN05214-03 - Bulldozer D375A-6R Shop Manual (SN65001&up).pdf
TEN00140-00 - Bulldozer GALEO D375A-5E0 Operation & Maintenance Manual (SN50001&up).pdf
TEN00195-03 - Bulldozer D375A-5 Operation & Maintenance Manual (SN18001&up).pdf
TEN00196-03 - Bulldozer D375A-5 Operation & Maintenance Manual (SN18052&up).pdf
TEN00197-03 - Bulldozer D375A-5 Operation & Maintenance Manual (SN18200&up).pdf
TEN00258-02 - Bulldozer D375A-5E0 Operation & Maintenance Manual (SN50065&up).pdf
TEN00272-00 - Bulldozer D375A-5E0 Operation & Maintenance Manual (SN50065&up).pdf
TEN00305-02 - Bulldozer D375A-5E0 Operation & Maintenance Manual (SN50091&up).pdf
TEN00333-02 - Bulldozer D375A-6 Operation & Maintenance Manual (SN60001&up).pdf
TEN00477-02 - Bulldozer D375A-6 Operation & Maintenance Manual (SN60018&up).pdf

EXCERPT:

DISASSEMBLY AND ASSEMBLY - REMOVAL AND INSTALLATION OF RADIATOR ASSEMBLY
REMOVAL
- Disconnect the cable from the negative (–) terminal of the battery.
1. Drain coolant.
2. Remove inspection cover (17).
3. Disconnect front lamp connector (CN-202) (1).
4. Using eyebolts, lift off radiator top cover (2). Radiator top cover: 76kg
5. Disconnect radiator inlet hose (3) and aeration hose (4).
6. Remove ground wiring (CN-GND4) (5).
7. Disconnect wiring clamps (6) (4 places), and move wiring towards left side of radiator.
8. Disconnect sub tank hose (7).
9. Disconnect radiator water level sensor connector (CN-405) (8).
10. Remove windbreaker plate (9).
11. Using eyebolts, sling radiator assembly, then remove 2 each of left and right top mount bolts (10).
12. Remove 2 covers (11).
13. Open guard (12).
14. Remove windbreaker plate (13).
15. Disconnect radiator outlet tube (14).
16. Remove bottom mount bolt (15).
17. Lift off radiator assembly (16). Radiator assembly: 390kg
INSTALLATION
• Carry out installation in the reverse order to removal. Radiator inlet hose clamp: 882 ± 98Ncm {90 ± 10kgcm}. Aeration hose clamp: 333.2 ± 49Ncm {34 ± 5kgcm}
Refilling with water
Add water through water filler to the specified level.
Run the engine to circulate the water through the system. Then check the water level again.
...