Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Komatsu PC340-6K, PC340LC-6K, PC340NLC-6K, PC340LC-7, PC340LC-7K, PC340NLC-7, PC340NLC-7K Hydraulic Excavator. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your PC340 like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Komatsu PC340-6K, PC340LC-7, PC340LC-6K, PC340LC-7K, PC340NLC-7, PC340NLC-6K, PC340NLC-7K is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

"Shop Manual (UEN00262-00).pdf"
910 pages; Komatsu GALEO PC340LC-7, PC340NLC-7 Hydraulic Excavator Shop Manual
SERIAL NUMBERS: K45001 AND UP

"Shop Manual (UEBM001501).pdf"
630 pages; Komatsu PC340LC-7K, PC340NLC-7K Hydraulic Excavator Shop Manual
SERIAL NUMBERS: K40001 AND UP

"Shop Manual (UEBM000901).pdf"
748 pages; Komatsu PC340-6K, PC340LC-6K, PC340NLC-6K Hydraulic Excavator Shop Manual
SERIAL NUMBERS: K32001 and UP, K34001 and up

"Shop Manual (EEBM000804).pdf"
738 pages; Komatsu PC340-6K, PC340LC-6K, PC340NLC-6K Hydraulic Excavator Shop Manual
SERIAL NUMBERS: K30001 and UP

"Operation & Maintenance Manual (UEAM001505).pdf"
380 pages; Komatsu PC340LC-7K, PC340NLC-7K Hydraulic Excavator Operation & Maintenance Manual
SERIAL NUMBERS: K40001 AND UP

"Operation & Maintenance Manual (UEAM001500).pdf"
316 pages; Komatsu PC340LC-7K, PC340NLC-7K Hydraulic Excavator Operation & Maintenance Manual
SERIAL NUMBERS: K40001 AND UP

"Operation & Maintenance Manual (EEAM008000).pdf"
258 pages; Komatsu PC340-6K, PC340LC-6K, PC340NLC-6K Hydraulic Excavator Operation & Maintenance Manual
SERIAL NUMBERS: K30001 AND UP

EXCERPT:
50 Disassembly and assembly
Removal and installation of front window assembly
- Lower the work equipment to the ground and stop the engine.
- To replace the front window glass, the front window assembly must be removed from the operator's cab. The procedure for removing and installing the front window assembly (front frame and front window glass) is explained below.
Removal
1. Raise the front window assembly to the ceiling and fix it with the rear locks (on both sides).
2. Remove left corner blocks (1) and (2) and right corner block (3). [*1]
3. Remove left striker bolt (4), right striker bolt (5), left corner block bracket, and right corner block bracket (7). [*2]
4. Install left striker bolt (4) to the operator's cab again and tighten it lightly.
a This bolt will be used to hang the pull-up assist cable in step 8.
5. Release the rear locks.
6. Lower the front window assembly carefully a little. Put out rollers (8) and (9) under the both sides of the front window through the portion from which the corner blocks were removed in step 3 (the portion where the rail is open) and hold them.
7. Remove rollers (8) and (9) under the both sides of the front window.
...