Logo

Cart

Click title to display cart contents.
0 Items $0.00

New Holland / Ford Tractors TW5, TW15, TW25, TW35, 8530, 8630, 8730, 8830 Factory Service & Shop Manual

Catalog: 

Make: 

Model: 

US Dollar: $35.00

New Holland / Ford Tractors TW5, TW15, TW25, TW35, 8530, 8630, 8730, 8830 Factory Service & Shop Manual

Complete workshop repair service manual with electrical wiring diagrams for New Holland / Ford Tractors TW5, TW15, TW25, TW35, 8530, 8630, 8730, 8830. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This New Holland / Ford Tractors TW5, TW15, TW25, TW35, 8530, 8630, 8730, 8830 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

1,466 pages, bookmarked, Searchable, Printable, high quality PDF
New Holland / Ford TW5, TW15, TW25, TW35, 8530, 8630, 8730, 8830 Service & Repair Manual.pdf
1,466 pages; 40000580

EXCERPT:
PART4 - CLUTCHES

RE-ASSEMBLY

Prior to re-assembly, coat the sides of the pressure plate drive lugs, where the release levers rub, with a silicon base grease.

RE-ASSEMBLY AND ADJUSTMENT USING TOOL NO. FT.7110 (SW 12B)

NOTE: A new clutch assembly should be checked and, if necessary, adjusted. Follow Steps 1, 3 and 6 - 14.

1. Locate the clutch pressure plate assembly centrally on the base plate with the four Disc Spacers, Tool No. FT.7110-2/1 (SW128-2), between the pressure plate and the base plate of the tool.

2. Locate all springs in their original positions as previously noted. Place the clutch cover over the springs and align mating holes and reference marks. Do not move the springs.

Figure 9
Settling Clutch Mechanism
1. Actuator Cam Platform Extension, Tool No. STM no7
2. Clutch Assembly
3. Base Plate, Tool No. STM n04
4. Bolt, Tool No. FT.7110/25 (SW 12B/25)
5. Actuator, Tool No. FT.7110/28 (SW 12B/28)

3. Secure the assembly to the base plate with the eight special Bolts, Tool No. SW 128/25, Figure 9. Tighten the bolts evenly and diagonally across the clutch.

4. Adjust the alignment of the parts as necessary and ensure the yokes and lugs pass through the clutch cover and do not bind on assembly.

5. Install the adjusting nuts on the yokes to keep them centered in the cover holes.

6. Locate the Actuator Cam Platform Extension, Tool No. STM no7, on the threaded pillar of the actuator with the flange of the extension facing downwards. Screw the actuator into the Spider, Tool No. 99MA/1, of the tool base until the flange of the extension contacts the clutch release levers, Figure 9.

7. Operate the handle of the actuator to depress the clutch release levers and repeat several times to settle the clutch mechanism. Remove the actuator and extension.

NOTE: When preparing a new clutch assembly, remove the eight bolts securing the four thrust plates.

New Holland / Ford Tractors TW5, TW15, TW25, TW35, 8530, 8630, 8730, 8830 Factory Service & Shop Manual

Additional 10% off on US$30+ order paid with Credit Card: 10POFF.

To pay in your local currency (EURO, GBP, AUD, CAD, HKD, JPY, etc.), please contact us.