Complete workshop & service manual with electrical wiring diagrams for Bobcat 444, 500, 600, 600D, 610, 611, M444, M500, M600, M610 Loader. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Bobcat Bobcat 444, 500, 600, 600D, 610, 611, M444, M500, M600, M610 Loader service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

6509710 (3-97) - M444, M500, M600 Operation & Maintenance Manual.pdf
6556099 (11-86) - 610 Operation & Maintenance Manual.pdf
6556100 (3-77) - 611 Operation & Maintenance Manual.pdf
6556276 (6-87) - 600, 600D, 610, 611 Service Manual.pdf
6556520 (3-87) - 444, 500, 600 Service Manual Supplement.pdf
6556602 - M444, M500, M600, M610 Service Manual.pdf
Supplement to 6556276 - 444, 500, 600 Service Manual Supplement.pdf

EXCERPT:
GENERAL SERVICE
CHANGING AND ADDING HYDRAULIC OIL . . . . . 1–3 1–2
CRANKCASE AIR VENT (DEUTZ) . . . . . . 1–15 1–7
CRANKCASE AIR VENT (WISCONSIN) . . . . . . . . . 1–14 1–7
DISTRIBUTOR MAINTENANCE (WISCONSIN) . . . 1–22 1–10
ENGINE AIR CLEANER . . . . . . . . 1–6 1–4
ENGINE COOLING SYSTEM . . . 1–19 1–8
ENGINE OIL . . . . . . . . . . 1–9 1–5
ENGINE OIL FILTER (DEUTZ) . . . . . . . . . . 1–12 1–6
ENGINE OIL FILTER (WISCONSIN) . . . . . 1–11 1–6
FUEL ADJUSTMENT (PETTER) . . . . . . . . 1–18 1–8
FUEL FILTERS . . . . . . . 1–17 1–7
FUEL SPECIFICATIONS . . . . . . . 1–16 1–7
HEAVY DUTY AIR CLEANER . . . 1–8 1–4
HYDRAULIC FLUID FILTER CHANGE . . . 1–5 1–3
IGNITION TIMING (WISCONSIN ENGINE) . . . . . . . 1–21 1–9
LOADER LUBRICATION . . . . . . . 1–2 1–2
OIL FILTER (PETTER) . . . . . . . . . 1–13 1–6
OIL SPECIFICATIONS FOR ENGINES . . . . . . . . . . 1–10 1–5
OIL TYPE AIR CLEANER . . . . . . 1–7 1–4
REMOVING WATER FROM HYDRAULIC TANKS . . . . . . . . . 1–4 1–2
SPARK PLUG (WISCONSIN) . . . 1–23 1–10
TIRES . . . . . . . 1–1 1–2
WATER SCRUBBER MUFFLER (600 DIESEL) . . . 1–20 1–8
…
5–8 DISASSEMBLY OF THE FUEL BOWL
1. Remove the 1/2 inch (12,7 mm) plug (Item 13) from the bottom of the fuel bowl. Remove the fiber washer (Item 14).
2. Remove main jet (Item 15) and fiber washer (Item 16) from the threaded passage near the bottom of fuel bowl.
3. Remove main outlet jet (Item 17) with its fiber washer (Item 18) from center of fuel bowl (11/32 inch (8,6 MM) wrench to remove).
4. Mark the choke bracket (Item 19), choke lever (Item 20) and air intake housing as a guide to correct assembly.
5. Remove choke lever spring (Item 21). Close choke and remove choke plates screw (Item 22), choke plate and shaft (Item 23). (Note the position of choke plate stop in air intake).
6. Remove choke bracket screws and choke bracket.
Clean all metal parts, using a carburetor parts cleaner. Wash in solvent. Clean out all passages and channels in carburetor with air. Reverse air flow through each passage to remove all dirt.
NOTE: Never use a hard wire or drill to clean out jets. Inspect all parts and install any damaged or worn parts. A repair kit should be used. For correct repair kit, see Bobcat Parts Book.
5–9 TO ASSEMBLE FUEL BOWL AND INTAKE ASSEMBLY
1. Install choke shaft seal and holder using a bushing driver to drive holder into housing until even with machined surface (Fig. 5–8). Follow same procedure for other side.
2. Install choke shaft (Item 23) through seals and holders in position in air intake body. Install choke plate (Item 22) in cut out of choke shaft. Check that choke plate release valve is in same position as when it was disassembled. Install choke plates screws using a small screwdriver.
3. Put choke shaft bracket (Item 19) over choke shaft and fasten bracket to air intake in same position as when removed. Tighten screws.
4. Fasten choke lever spring (Item 21) to choke lever and choke bracket.
5. Put fiber washer (Item 18) over threads of main outlet jet (Item 17). Install main outlet jet in bowl assembly and tighten.
6. Put fiber washer (Item 16) on main jet (Item 15) and install main jet in threaded hole near bottom of bowl.
7. Install hex plug (Item 13) and gaskets (Item 14) and tighten.
…