Complete workshop repair & service manual with electrical wiring diagrams for Bobcat 753 Loader. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Bobcat 753 Loader service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

6720326 (8-90) - 753 Loader Service Manual.pdf
6720326 (8-90) - 753 Service Manual.pdf
6720583 (10-92) - 753, 753H Operation & Maintenance Manual.pdf
6722443 (3-93) - 753, 753H Operation & Maintenance Manual.pdf
6722761 (11-98) - 753, 753H Operation & Maintenance Manual.pdf
6722905 (11-01) - 753, 753H Operation & Maintenance Manual.pdf
6722925 (7-00) - 753L Operation & Maintenance Manual.pdf
6900090 (6-97) - 753, 753 High Flow Service Manual.pdf
6900374 (6-00) - 753, 753H (Foot Pedal & Hand Controls) Operation & Maintenance Manual.pdf
6900438 (11-01) - 753 Operation & Maintenance Manual.pdf
6900787 (9-00) - 753 Operation & Maintenance Manual.pdf
6900969 (12-06) - 753 Operation & Maintenance Manual.pdf
6900976 (2-06) - 753 (G Series) Service Manual.pdf
6900976 (9-10) - 753 (G Series) Service Manual.pdf

EXCERPT:
CONTENTS
FOREWORD. . . . . . . . . . . . . . . II
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . V
SERIAL NUMBER LOCATIONS . . . . . . . . . . . . . . IX
DELIVERY REPORT. . . . . . . . . IX
LOADER IDENTIFICATION . . . . . . . . . . . . . . . . . X
SAFETY AND MAINTENANCE. . . . . . . . . . . . 10-01
HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . 20-01
HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . 30-01
DRIVE SYSTEM . . . . . . . . . 40-01
MAIN FRAME . . . . . . . . . . . 50-01
ELECTRICAL SYSTEM & ANALYSIS. . . . . . . 60-01
ENGINE SERVICE . . . . . . . 70-01
HEATER . . . . . . . . . . . . . . . 80-01
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . SPEC-01
…
DRIVE COMPONENTS
Axle Seal Removal And Installation
Figure 40-20-1
The tools listed are needed for the following procedure:
Axle Hub Puller Tool
MEL1399 - Seal Driver Tool
MEL1242 - Power Ram (may be used if desired)
To loosen the axle hub mounting bolt (Item 1) [Figure 40-20-1], use the following procedure:
Before lifting and blocking the loader, loosen the hub mounting bolt (Item 1) [Figure 40-20-1].
NOTE: If the axle and bearings are being replaced, also loosen the sprocket mounting bolt inside the chaincase before lifting and blocking the loader. (See Axle Sprocket And Bearings
Removal And Installation on Page 40-20-3.)
Lift and block the loader. (See LIFTING AND BLOCKING
THE LOADER on Page 10-10-1.)
Remove the front tire/wheel assembly.
Installation: Tighten the wheel mounting nuts to 105-115 ft.-lbs. (142-156 Nm) torque.
Remove the hub mounting bolt (Item 1) [Figure 40-20-1] and washer from the axle.
Installation: Tighten the hub mounting bolt to 575-625 ft.-lbs. (780-848 Nm) torque.
Remove two of the wheel mounting studs (Item 2)
[Figure 40-20-1].
Use a wheel mounting nut on each stud and remove the two studs with a hammer.
Installation: Support the flange of the axle hub and install the two studs with a hammer. A hydraulic press can also be used to install the studs.
…