Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Ford Escort 1981-2003, Mercury Tracer 1990-1999. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This Ford Escort 1981-2003, Mercury Tracer 1990-1999 manual is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

BONUS:
1981-1989 Ford Escort (up to H registration) Petrol+.pdf
1991-1996 Ford Escort, Mercury Tracer.pdf
...

EXCERPT:
1. Remove the hood.
2. Relieve the fuel system pressure. For additional information, refer to FUEL SYSTEM PRESSURE RELEASE .
3. Remove the battery (10653).
4. Remove the battery tray (10732).
5. Disconnect the heated oxygen sensor (HO2S) (9F472). For additional information, refer to HEATED OXYGEN SENSOR .
6. Drain the engine coolant. For additional information, refer to ENGINE COOLING .
7. Recover the A/C refrigerant. For additional information, refer to RECOVERY/EVACUATION & RECHARGING .
8. Remove the catalytic converter.
9. Remove the radiator splash shield. .
10. Disconnect the starter motor wiring. For additional information, refer to REMOVAL & INSTALLATION .
11. Remove the drive belt (8620). For additional information, refer to SPECIFICATIONS & DRIVE BELT ROUTING .
12. Remove the A/C compressor (19703). For additional information, refer to COMPRESSOR .
13. Disconnect the lower radiator hose and heater hose.
Fig. 142: Disconnecting Lower Radiator Hose And Heater Hose (Automatic Transmission)
14. Disconnect the power steering pressure line. For additional information, refer to POWER STEERING .
15. Remove the torque converter inspection cover.
16. Remove the torque converter nuts.
Fig. 144: Removing Torque Converter Nuts (Automatic Transmission)
17. Remove the front roll restrictor.
Fig. 145: Removing Front Roll Restrictor (Automatic Transmission)
18. Remove the nuts.
Fig. 146: Removing Nuts (Automatic Transmission)
19. Remove the driveshafts (4602). For additional information, refer to AXLE SHAFTS - FRONT .
20. Disconnect the transaxle cooler lines. For additional information, refer to REMOVAL & INSTALLATION .
21. Remove the transaxle cooler line bolts.
Fig. 147: Removing Transaxle Cooler Line Bolts (Automatic Transmission)
22. Remove the air cleaner assembly. .
23. Disconnect the transaxle shift cable.
Fig. 148: Disconnecting Transaxle Shift Cable (Automatic Transmission)
24. Disconnect the fuel charging wiring (9D930) from the transaxle internal wiring harness connector, turbine shaft speed sensor, transaxle range sensor and the heated oxygen sensor connector.
Fig. 149: Disconnecting Connectors (Automatic Transmission)
25. Remove the radiator (8005), fan shroud (8146) and fan motor (8C607) as an assembly. For additional
information, refer to ENGINE COOLING .
26. Remove the transaxle cooler lines. For additional information, refer to REMOVAL & INSTALLATION .
27. Disconnect the accelerator cable (9A758) and the speed control actuator cable (9A825).
Fig. 150: Disconnecting Accelerator Cable And Speed Control Actuator Cable (Automatic Transmission)
28. Disconnect the accelerator cable, the speed control actuator cable and the brackets.
…