Complete workshop repair & service manual with electrical wiring diagrams for Ford Explorer, Mercury Mountaineer 2006. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Ford Explorer, Mercury Mountaineer 2006 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

· U62 — Explorer, 4x2, XLS, MPV
· U63 — Explorer, 4x2, XLT, MPV
· U64 — Explorer, 4x2, Eddie Bauer, MPV
· U65 — Explorer, 4x2, Limited, MPV
· U72 — Explorer, 4x4, XLS, MPV
· U73 — Explorer, 4x4, XLT, MPV
· U74 — Explorer, 4x4, Eddie Bauer, MPV
· U75 — Explorer, 4x4, Limited, MPV
· U36 — Mountaineer, 4x2, base-level model, MPV
· U37 — Mountaineer, 4x2, mid-level model, MPV
· U38 — Mountaineer, 4x2, high-level model, MPV
· U46 — Mountaineer, all-wheel drive (AWD), base-level model, MPV
· U47 — Mountaineer, AWD, mid-level model, MPV
· U48 — Mountaineer, AWD, high-level model, MPV

· E — 4.0L, SOHC, V6, EFI
· 8 — 4.6L, 3-valve, V8, EFI

EXCERPT:
2006 Explorer/Mountaineer
Workshop Manual
Quick Links
Introduction
Specifications
Metrics
Torque Wrench Adapter Formulas
Acronyms
Alphabetical Index
Table of Contents
1: General Information
00: Service Information
2: Chassis
04: Suspension
05: Driveline
06: Brake System
11: Steering System
3: Powertrain
03: Engine
07: Automatic Transmission
08: Manual Transmission, Clutch and Transfer Case
09: Exhaust System
10: Fuel System
4: Electrical
12: Climate Control System
13: Instrumentation and Warning Systems
14: Battery and Charging System
15: Audio Systems
17: Lighting
18: Electrical Distribution
19: Electronic Feature Group
5: Body and Paint
01: Body
02: Frame and Mounting
…
GROUP 03: Engine
SECTION 303-00: Engine System — General Information
SECTION 303-01A: Engine — 4.0L SOHC
SECTION 303-01B: Engine — 4.6L (3V)
SECTION 303-03: Engine Cooling
SECTION 303-04A: Fuel Charging and Controls — 4.0L SOHC
SECTION 303-04B: Fuel Charging and Controls — 4.6L (3V)
SECTION 303-05: Accessory Drive
SECTION 303-06: Starting System
SECTION 303-07A: Engine Ignition — 4.0L SOHC
SECTION 303-07B: Engine Ignition — 4.6L (3V)
SECTION 303-08: Engine Emission Control
SECTION 303-12: Intake Air Distribution and Filtering
SECTION 303-13: Evaporative Emissions
SECTION 303-14: Electronic Engine Controls
…
"Removal and Installation"
"1. Remove the intake manifold. For additional information, refer to Intake Manifold in this section."
"2. Disconnect the Camshaft Position (CMP) sensor electrical connector."
"3. Disconnect the ignition coil electrical connector. Detach the wiring harness retainer."
"4. Disconnect the 3 fuel injector electrical connectors. Detach the wiring harness retainers."
"5. Remove the PCV valve tube."
"6. Disconnect the PCV valve electrical connector."
"7. Detach the spark plug wire retainers."
"8. Remove the 6 bolts and the valve cover."
• To install, tighten to 10 Nm (89 lb-in)."
"NOTICE: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean sealing surfaces. These tools cause scratches and gouges which make leak paths. Use a plastic scraping tool to remove all traces of the old valve cover gasket."
"9. Clean and inspect the sealing surfaces and the gasket. Install a new gasket if necessary."
"10. To install, reverse the removal procedure."
…