Complete workshop repair service manual with electrical wiring diagrams for Ford Explorer, Mercury Mountaineer 2012. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Ford Explorer, Mercury Mountaineer 2012 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

• K7B - Explorer, Front Wheel Drive (FWD)
• K7D - Explorer, Front Wheel Drive (FWD), XLT
• K7F - Explorer, Front Wheel Drive (FWD), Limited
• K8B - Explorer, All-Wheel Drive (AWD)
• K8D - Explorer, All-Wheel Drive (AWD), XLT
• K8F - Explorer, All-Wheel Drive (AWD) , Limited

• 8 - 3.5L, V6, gas
• 9 - 2.0L, four-cylinder Gasoline Turbocharged Direct Injection (GTDI)

EXCERPT:
2012 Explorer
Workshop Manual
INTRODUCTION
Master DTC Chart
Diagnostic Methods
Metrics
Torque Wrench Adapter Formulas
1: GENERAL INFORMATION
00: SERVICE INFORMATION
2: CHASSIS
04: SUSPENSION
05: DRIVELINE
06: BRAKE SYSTEM
11: STEERING SYSTEM
3: POWERTRAIN
03: ENGINE
07: AUTOMATIC TRANSMISSION
08: MANUAL TRANSMISSION, CLUTCH, AND TRANSFER CASE
09: EXHAUST SYSTEM
10: FUEL SYSTEM
4: ELECTRICAL
12: CLIMATE CONTROL SYSTEM
13: INSTRUMENTATION AND WARNING SYSTEMS
14: BATTERY AND CHARGING SYSTEM
15: AUDIO SYSTEM
17: LIGHTING
18: ELECTRICAL DISTRIBUTION
19: ELECTRONIC FEATURE GROUP
5: BODY AND PAINT
01: BODY
02: FRAME AND MOUNTING
…
03: ENGINE
303-00 Engine System - General Information
303-01 Engine - 2.0L GTDI
303-01 Engine - 3.5L Ti-VCT
303-03 Engine Cooling
303-04 Fuel Charging and Controls - 2.0L GTDI
303-04 Fuel Charging and Controls - 3.5L Ti-VCT
303-04 Turbocharger - 2.0L GTDI
303-05 Accessory Drive
303-06 Starting System
303-07 Engine Ignition - 2.0L GTDI
303-07 Engine Ignition - 3.5L Ti-VCT
303-08 Engine Emission Control
303-12 Intake Air Distribution and Filtering
303-13 Evaporative Emissions
303-14 Electronic Engine Controls
…
Diagnostic Overview
Seat Latch Motor and Latch Switch Functional Test - LH
Refer to Wiring Diagrams Cell 120 for schematic and connector information.
Normal Operation and Fault Conditions
The Power-Fold Seat Module (PFSM) supplies voltage and ground to the seat latch release motor to electronically release the seat latch from the latched position (seat folded and latched to the floor) when the third row seat control switch sends a signal to the Power-Fold Seat Module (PFSM) to move the seat to the STOW position. The Power-Fold Seat Module (PFSM) monitors the latch switch to determine if the position of the latch is closed or released. If the seat latch does not release, the latch must be mechanically released to move the seat from the latched home position. If a fault is detected during a seat operation, the seat may enter a faulted state. When the seat is in a faulted state, the seat backrest and cushion fold together to prevent the seat from being occupied.
Visual Inspection and Diagnostic Pre-checks
Verify good battery condition before diagnosing the Power-Fold Seat Module (PFSM) system. Poor battery condition may interfere with Power-Fold Seat Module (PFSM) operation. If battery voltage drops below 10 volts, seat movement does not start. If battery voltage drops below 8 volts, a started seat movement stops.
…