Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Scion xA 2003-2007. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Scion xA 2003-2007 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

MAKE: Scion
MODEL: xA
YEAR: 2003 2004 2005 2006 2007

EXCERPT:
1NZ-FE EXHAUST – EXHAUST PIPE

REMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
2. REMOVE SHIFT LEVER KNOB (for Manual Transaxle)
3. REMOVE REAR CONSOLE BOX (See page IP-26)
4. REMOVE FRONT FLOOR PANEL BRACE
(a) Remove the 2 bolts and floor panel brace.
5. REMOVE TAILPIPE
(a) Remove the bolt and clamp.
(b) Disconnect the 2 exhaust pipe supports, and remove the tailpipe and gasket.
6. REMOVE FRONT EXHAUST PIPE
(a) Disconnect the 2 heated oxygen sensor connectors.
(b) Remove the grommet.
(c) Remove the 2 bolts and 2 compression springs.
(d) Disconnect the 2 exhaust pipe supports, and remove the front exhaust pipe.
7. REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 1)
(a) Using SST, remove the sensor from the front exhaust pipe. SST 09224-00010
8. REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
(a) Using SST, remove the sensor from the front exhaust pipe. SST 09224-00010

INSTALLATION
1. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
(a) Using SST, install the sensor to the front exhaust pipe. SST 09224-00010
Torque: 40 N*m (408 kgf*cm, 30 ft.*lbf) for use with SST 44 N*m (449 kgf*cm, 32 ft.*lbf) for use without SST
HINT: Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
2. REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 1)
(a) Using SST, install the sensor to the front exhaust pipe. SST 09224-00010
Torque: 40 N*m (408 kgf*cm, 30 ft.*lbf) for use with SST 44 N*m (449 kgf*cm, 32 ft.*lbf) for use without SST
HINT: Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
3. INSTALL FRONT EXHAUST PIPE
(a) Using a vernier caliper, measure the free length of the compression spring.
Minimum length: 40.5 mm (1.594 in.)
If the length is less than the minimum, replace the compression spring.
(b) Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold.
NOTICE:
• Tap in the gasket in the correct direction.
• Do not reuse the removed gasket.
• Do not to push in the gasket while installing the exhaust pipe.
(c) Connect the 2 exhaust pipe supports, and install the exhaust pipe.
...