Complete digital official shop manual contains service, maintenance, and troubleshooting information for the Chevrolet Citation, Corsica, El Camino 1980-1996. Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your vehicle like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for Chevrolet Citation, Corsica, El Camino 1980-1996 is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

Chevrolet Citation 1980-1983
Chevrolet Citation II 1984-1985
Chevrolet Corsica 1987-1996
Chevrolet El Camino 1978-1987

EXCERPT:
1996-97 ENGINES
2.2L 4-Cylinder VIN 4
ENGINE IDENTIFICATION
VEHICLE IDENTIFICATION NUMBER (VIN)
The VIN is stamped on a metal pad located near lower left corner of windshield.
A "4" in the eighth character of VIN identifies 2.2L 4-cylinder engine.
ENGINE BUILD DATE & ENGINE CODE
The engine build date (month and day) and the engine code are stamped on left side of cylinder block, near cylinder head. See Fig. 1. Engine code LN2 indicates 2.2L 4-cylinder engine.
PARTIAL VIN
A partial VIN (9 characters) is stamped on lower left side of cylinder block, at cylinder block-to-transmission flange. See Fig. 1.
Fig. 1: Locating Engine Build Date, Engine Code & Partial VIN
ADJUSTMENTS
VALVE CLEARANCE ADJUSTMENT
Engine is equipped with non-adjustable hydraulic valve lifters.
REMOVAL & INSTALLATION
CAUTION: When battery is disconnected, vehicle computer and memory systems may lose memory data.
Driveability problems may exist until computer systems have completed a relearn cycle. See COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION before disconnecting battery.
NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before removal.
FUEL PRESSURE RELEASE
Except Beretta & Corsica
1. Loosen fuel tank filler cap to release tank vapor pressure. Raise and support vehicle. Disconnect fuel pump electrical connector at fuel tank. Start and run engine until engine stops.
2. Engage starter for at least 3 seconds to ensure remaining fuel pressure is released. Disconnect negative battery cable. Reconnect fuel pump connector.
Since some residual pressure may exist in fuel system, cover fuel line fitting with a shop towel before loosening.
Beretta & Corsica
1. Loosen fuel tank filler cap to release tank vapor pressure. Remove fuse No. 16 (20-amp fuel pump fuse) from fuse block, located below left side of instrument panel. Start and run engine until engine stops.
2. Engage starter for at least 3 seconds to ensure remaining fuel pressure is released. Disconnect negative battery cable. Install fuse. Since some residual pressure may exist in fuel system, cover fuel line fitting with a shop towel before loosening fitting.
COOLING SYSTEM BLEEDING
Cavalier & Sunfire
DRAINING & FILLING COOLING SYSTEM
Draining Procedure
1. Park the vehicle on a level surface.
2. Remove the surge tank cap.
3. Raise and support the vehicle.
4. Place a drain pan under the drain cock.
5. Open the radiator drain cock.
6. Drain the cooling system.
7. Inspect the engine coolant for the following:
Discolored - follow the flush procedure. Refer to Flushing.
Normal in appearance - follow the filling procedure.
...