Complete digital official shop manual contains service, maintenance, and troubleshooting information for the 2006-2009 Harley Davidson Touring (TLE, TLE-U SIDECARS, FLHR, FLHRC, FLHRS, FLHX, FLHT, FLHTC, FLHTCU, FLTR, DOMESTIC and INTERNATIONAL Models). Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your bike like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This motorbike manual for Harley Davidson Touring (TLE, TLE-U SIDECARS, FLHR, FLHRC, FLHRS, FLHX, FLHT, FLHTC, FLHTCU, FLTR, DOMESTIC and INTERNATIONAL Models) is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

MAKE: Harley Davidson
--- --- --- --- --- --- --- --- ---
MODEL: Touring (TLE, TLE-U SIDECARS, FLHR, FLHRC, FLHRS, FLHX, FLHT, FLHTC, FLHTCU, FLTR, DOMESTIC and INTERNATIONAL Models)
--- --- --- --- --- --- --- --- ---
YEAR: 2006, 2007, 2008, 2009

"'06.pdf"
986 pages; 2006 Touring Service Manual

"'09 (99483-09).pdf"
702 pages; 2009 Touring Models Service Manual

EXCERPT:

INSTALLATION
1. Fit halves of the headlamp nacelle together engaging the holes in the nacelle with the left and right side fork bracket studs.
2. See Figure 2-162. Reaching inside the headlamp nacelle, connect accessory switch connector [67] and auxiliary lamp switch connector [109].
3. See Figure 2-161. If disassembled, install Phillips screw, flat washer and Keps nut on the handlebar clamp shroud.
4. Part the halves of the headlamp nacelle slightly. With the flat washer on the inboard side of the nacelle, slide the shroud rearward running the shaft of the Phillips screw down the gap. Position the shroud over the flange at the top of the nacelle.
5. Mate the halves of the headlamp nacelle and tighten the Phillips screw to 10-20 in-lbs (1.1-2.3 Nm).
6. Install two Phillips screws to secure handlebar clamp shroud to the fork lock mechanism. Alternately tighten screws to 10-20 in-lbs (1.1-2.3 Nm). Install fork lock plate.
NOTE
To avoid possible damage to the brake hose and/or handlebar switch wires, verify that trim strips are installed on inside edges of the headlamp nacelle. Cutting or severe chafing of the brake
hose and/or handlebar switch wires could cause loss of function while riding.
7. Verify that trim strips are installed on inside edges of headlamp nacelle. Install new trim strips if cracked, damaged or missing.
8. Inserting the weld stud on the chrome strip into the hole at the top of the headlamp nacelle, reach inside the nacelle to install flange nut. Tighten flange nut to 15-20 in-lbs (1.7-2.3 Nm).
9. Install the grommets on the left and right side fork studs.
10. Slide the auxiliary lamp bracket onto the left and right side fork bracket studs. Verify that the four grommets are in place on the inboard side of the auxiliary lamp brackets.
...