Complete workshop repair & service manual with electrical wiring diagrams for Suzuki AN250/AN400/AN650. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

Suzuki AN250/AN400/AN650 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

Suzuki AN250 K3 K4 Manual de Servicio (ES).pdf
Suzuki AN250 Burgman (AN250K3, AN250K4) 2003-2004 Service Manual in Spanish; 395 pages
Suzuki AN650 K3 Service Manaul (EN).pdf
Suzuki AN650 (AN650K3) Burgman 2003 Service Manual; 463 pages
Suzuki AN400 K3 Service Manaul (EN).pdf
Suzuki AN400 (AN400K3) Burgman 2003 Service Manual; 406 pages
Suzuki AN650 1999er Model Wartungsanleitung (DE).pdf
Suzuki AN400 (AN400X) Burgman 1999 Wartungsanleitung; 292 pages

EXCERPT:
GROUP INDEX
GENERALINFORMATION
PERIODIC MAINTENANCE
ENGINE
FISYSTEM
FUEL SYSTEM AND THROTTLE
BODY
COOLING AND LUBRICATION
SYSTEM
CHASSIS
ELECTRICAL SYSTEM
SERVICING INFORMAnON
EMISSION CONTROL
INFORMATION
…
6-2 COOUHGAHOW8RICAT10HSYSTEM
COOLING SYSTEM
DESCRIPTION
The engine is cooled by the forced circulation of engine coolant, using a high-capacity, centrifugal water pump, through water jackets formed in the cylinder and cylinder head, and through the radiator. The tube-and-fin type radiator is made of aluminum, which is characterized by lightness in weight and good heat dissipation.
…
ÍNDICE
INFORMACIÓN GENERAL
MANTENIMIENTO PERIÓDICO
MOTOR
SISTEMA FI
SISTEMA DE COMBUSTIBLE Y
CUERPO DEL ACELERADOR
SISTEMA DE REFRIGERACIÓN Y LUBRICACIÓN
CHASIS
SISTEMA ELÉCTRICO
INFORMACIÓN DE SERVICIO
INFORMACIÓN DE CONTROL
DE LA EMISIÓN
AN250K4 (MODELO '04)
…
4-42 SISTEMA FI
SENSORES
INSPECCIÓN DEL SENSOR CKP
El sensor de posición del cigüeñal está instalado en la cubierta del generador. (=> 4-23)
INSPECCIÓN DEL SENSOR IAP
El sensor de presión de entrada del aire se encuentra en el lado delantero de la caja del filtro de aceite. (=> 4-25)
INSPECCIÓN DEL SENSOR TP
El sensor de posición del acelerador está instalado en el lado derecho del cuerpo del acelerador. (=> 4-28)
PROCEDIMIENTO DE AJUSTE DEL TPS (=> 5-21)
INSPECCIÓN DEL SENSOR ECT
El sensor de temperatura del refrigerante del motor está instalado en la culata. (=> 4-31}
Sensor ECT: 18 N-m (1 ,8 kgf-m)
INSPECCIÓN DEL SENSOR IAT
El sensor de temperatura del aire de admisión está instalado debajo de la cámara de aire. (=> 4-33)
Sensor IAT: 3 N-m (0,3 kgf-m)
…
GROUP INDEX
GENERAL INFORMATION
PERIODIC MAINTENANCE
ENGINE
DRIVETRAIN
CVT
FI SYSTEM/ CVT SYSTEM
FUEL SYSTEM AND THROTTLE
BODY
COOLING AND LUBRICATION
SYSTEM
CHASSIS
ELECTRICAL SYSTEM
SERVICING INFORMATION
EMISSION CONTROL
INFORMATION
WIRING DIAGRAM
…
9·24 CHASSIS
HANDLEBAR COVER
After installing the handlebar covers, inspect clearance between the handlebar cover 1 and the front panel 2 /meter panel 3. If the clearance is less than 5 mm (0.2 in), adjust the handlebar position by rotating the handlebar so that the clearance would be more than 5 mm (0.2 in) all around the handlebar cover.
o Measure the clearance between the handlebar cover and the front panel/meter panel before removing the handlebar covers.
o Remove the handlebar covers. (=> 9·8)
o Loosen the handlebar clamp bolts 4.
o Rotate the handlebar according to the clearance measured above.
NOTE:
When rotating the handlebar by 0.5 mm (0.02 in) at the punch mark, the clearance would be varied as follows.
…

Suzuki AN250/AN400/AN650 Factory Service & Shop Manual