CNH Hydraulic hammers CB Series Workshop Repair & Service Manual

500+ total pages, bookmarked, Searchable, Printable, high quality PDF

603.67.220.00 - CNH Martelli idraulici Serie CB Service Manual (IT).pdf
603.67.221.00 - CNH Hydraulic hammers CB Serie Service Manual (EN).pdf
603.67.222.00 - CNH Marteaux hydrauliques Serie CB Service Manuel (FR).pdf
603.67.223.00 - CNH Martillos hidráulicos Serie CB Service Manual (ES).pdf
603.67.224.00 - CNH Hydraulikhämmer Serien CB Service Manual (DE).pdf

Complete digital official shop manual contains service, maintenance, and troubleshooting information for the CNH Hydraulic hammers CB Series (CB32, CB45, CB65, CB85, CB120, CB150, CB200S, CB260S, CB320S, CB400S, CB550S, CB700S). Diagnostic and repair procedures are covered in great detail to repair, maintain, rebuild, refurbish or restore your Case CB200 S - CB260 S - CB320 S - CB400 S - CB550 S - CB700 S like a professional mechanic in local service/repair workshop. This cost-effective quality manual is 100% complete and intact as should be without any missing pages. It is the same factory shop manual used by dealers that guaranteed to be fully functional to save your precious time.

This manual for CNH Hydraulic hammers CB Series is divided into different sections. Each section covers a specific component or system and, in addition to the standard service procedures, includes disassembling, inspecting, and assembling instructions. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. It is in the cross-platform PDF document format so that it works like a charm on all kinds of devices. You do not need to be skilled with a computer to use the manual.

EXCERPT:
Hydraulic hammers CB32 - CB45 - CB65 - CB85 - CB120 - CB150 ....7-22011GB
Hydraulic hammers CB200 S - CB260 S - CB320 S - CB400 S - CB550 S - CB700 S... 7-23861GB
...
TABLE OF CONTENTS
TECHNICAL SPECIFICATIONS ...3
Overall dimensions....3
SPECIFICATIONS...9
TORQUE SETTINGS ....10
TOOLS REQUIRED ....10
SPECIAL TOOLS ....11
REPLACING A HYDRAULIC HAMMER....12
HANDLING THE HYDRAULIC HAMMER ...14
IHYDRAULIC BREAKER OVERALL DIMENSIONS ...16
HAMMER HYDRAULIC PRESSURE DISCHARGE....17
LOCATION OF MAIN COMPONENTS ...18
CB32 - CB45 - CB65 - CB85 - CB120 - CB150 ....18
Removing the chassis plates ....19
Installing the chassis plates ....20
Releasing pressure in the low pressure accumulator....21
LOW PRESSURE ACCUMULATOR...21
Releasing pressure from the high pressure accumulator....24
HIGH PRESSURE ACCUMULATOR ....24
CHARGING THE ACCUMULATOR ....27
Charging....27
PRESSURE REGULATING VALVE....29
Assembly...30
TIE-RODS ...32
Removal ....32
CONTROL VALVE COMPONENTS (CB32 - CB85) ...35
Removal ....35
CONTROL VALVE BODY COMPONENTS (CB45 - CB65 - CB120 - CB150) ...38
Removal ....38
CYLINDER ....42
Removal ....42
FRONT PART....45
Removal ....45
CHANGING A TOOL ...48
Removal ....48
Installation ...49
Cre 7-22011GB
Issued 01- 052
CHANGING THE TOOL BUSHING...50
Removal ....50
Installation ...50
WEAR LIMITS ...51
Tool bushings....51
Tools ...51
INSPECTION AND MEASUREMENT OF HYDRAULIC HAMMER CIRCUIT...52
Measurement/inspection points ....52
MEASURING THE HYDRAULIC HAMMER OPERATING PRESSURE...54
OPERATING PRINCIPLES ...56
TROUBLESHOOTING ....59
...
Procedure for taking measurements
Procedure for measurement and adjustment of hydraulic hammer:
NOTE: Inspect and calibrate all the gauges: pressure gauges which are to be used. Change any defective pressure gauge.
NOTE: If the flow towards the hydraulic hammer is set by changing the speed of the engine, the flow should always be checked with the engine at maximum speed.
NOTE: It is strictly forbidden to operate the hydraulic hammer at a flow higher than the specifications.
...