Complete workshop & service manual for New Holland CX720, CX740, CX760, CX780, CX820, CX840, CX860, CX880 Combines. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This New Holland CX720, CX740, CX760, CX780, CX820, CX840, CX860, CX880 Combines service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

“6043400100 - CX720, CX740, CX760, CX780, CX820, CX840, CX860, CX880 Repair Manual.pdf”
4,282 PAGES

Contents
INTRODUCTION
DISTRIBUTION SYSTEMS A
PRIMARY HYDRAULIC POWER SYSTEM A.10.A
SECONDARY HYDRAULIC POWER SYSTEM A.12.A
HYDRAULIC COMMAND SYSTEM A.14.A
PNEUMATIC SYSTEM A.20.A
ELECTRICAL POWER SYSTEM A.30.A
LIGHTING SYSTEM A.40.A
ELECTRONIC SYSTEM A.50.A
POWER PRODUCTION B
ENGINE B.10.A
FUEL AND INJECTION SYSTEM B.20.A
AIR INTAKE SYSTEM B.30.A
EXHAUST SYSTEM B.40.A
ENGINE COOLANT SYSTEM B.50.A
LUBRICATION SYSTEM B.60.A
STARTING SYSTEM B.80.A
POWER TRAIN C
POWER COUPLING Fixed coupling C.10.B
TRANSMISSION Mechanical C.20.B
TRANSMISSION Hydrostatic C.20.F
PROCESS DRIVE Primary process drive C.50.B
TRAVELLING D
FRONT AXLE D.10.A
REAR AXLE D.12.A
2WD-4WD SYSTEM Hydrostatic D.14.E
STEERING Hydraulic D.20.C
SERVICE BRAKE Hydraulic D.30.C
PARKING BRAKE Hydraulic D.32.C
BODY AND STRUCTURE E
SHIELD E.20.A
OPERATOR AND SERVICE PLATFORM E.30.A
USER CONTROLS AND SEAT E.32.A
USER CONTROLS AND SEAT Operator seat E.32.C
USER PLATFORM E.34.A
ENVIRONMENT CONTROL Heating system E.40.B
ENVIRONMENT CONTROL Air-conditioning system E.40.C
ENVIRONMENT CONTROL Heating, ventilation and air-conditioning E.40.D
SAFETY SECURITY ACCESSORIES Safety E.50.B
TOOL POSITIONING G
LIFTING G.10.A
LEVELLING G.30.A
CROP PROCESSING K
FEEDING Reel feeding K.25.B
FEEDING Header feeding K.25.D
FEEDING Feeder housing K.25.E
THRESHING Conventional threshing K.40.B
SEPARATING Beating K.42.B
SEPARATING Rotary separator K.42.C
SEPARATING Straw walker K.42.E
SEPARATING Straw flow beater K.42.F
STORING AND HANDLING Grain storing K.60.B
CLEANING Primary cleaning K.62.B
CLEANING Tailings return system K.62.C
RESIDUE HANDLING Straw chopper K.64.C
RESIDUE HANDLING Spreader K.64.D
RESIDUE HANDLING Chaff blower K.64.F
UNLOADING Grain unloading K.72.B

EXCERPT:
TRAVELLING - REAR AXLE
Steering knuckle - Assemble (D.12.A.69 - F.10.A.20)
1. Using the locally fabricated tool, insert the bushing (1) and press into place until there is a maximum of 3mm(0.118 in) gap at the bottom of the bore. Apply a generous coating of grease to the bushing and fill the area above with the same grease. Install the seal (2) with the cupped side up.
2. Using the locally fabricated tool, insert the bushing (1) and press into place until there is a maximum of 3mm(0.118 in) gap at the bottom of the bore. Apply a generous coating of grease to the bushing and fill the area above with the same grease. Install the seal (2) with the cupped side up.
3. Inspect the machined ends (1) of the steering knuckle for wear, scratches and gouges. If the knuckle exhibits excessive play when assembled, replace the knuckle.
…