Complete workshop & service manual with electrical wiring diagrams for Ford Escape, Escape Hybrid, Mercury Mariner, Mariner Hybrid 2006. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

This Ford Escape, Escape Hybrid, Mercury Mariner, Mariner Hybrid 2006 service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.

· U02 — Escape, 2-wheel drive, XLS
· U03 — Escape, 2-wheel drive, XLT
· U04 — Escape, 2-wheel drive, Limited
· U92 — Escape, 4-wheel drive, XLS
· U93 — Escape, 4-wheel drive, XLT
· U94 — Escape, 4-wheel drive, Limited
· U95 — Escape, XLT — 2-wheel drive (Hybrid)
· U96 — Escape, XLT — 4-wheel drive (Hybrid)
· U56 — Mariner, 2-wheel drive
· U57 — Mariner, 4-wheel drive

· Z — 2.3L, 4-valve, in-line 4 cylinder
· 1 — 3.0L Modular, 6-cylinder, EFI, DOHC
· H — ATK-CYC, 2.3L, 4-valve PFI, in-line 4 cylinder, gas/electric (Hybrid)

EXCERPT:
2006 Escape/Mariner/Escape Hybrid/Mariner Hybrid
Workshop Manual
Quick Links
Introduction
Specifications
Metrics
Torque Wrench Adapter Formulas
Acronyms
Alphabetical Index
Table of Contents
1: General Information
00: Service Information
2: Chassis
04: Suspension
05: Driveline
06: Brake System
11: Steering System
3: Powertrain
03: Engine
07: Automatic Transmission
08: Manual Transmission, Clutch and Transfer Case
09: Exhaust System
10: Fuel System
4: Electrical
12: Climate Control System
13: Instrumentation and Warning Systems
14: Battery and Charging System
15: Audio Systems
17: Lighting
18: Electrical Distribution
19: Electronic Feature Group
5: Body and Paint
01: Body
02: Frame and Mounting
…
Exterior Lighting
NOTE: The smart junction box (SJB) is also known as the generic electronic module (GEM).
The exterior lighting consists of the following:
· Headlamps
· Front park/turn signal lamps
· Rear lamps
· High-mounted stoplamp
· Fog lamps
· Parking lamps
· License plate lamps
· Reversing lamps
· Side marker lamps
· Side turn signal lamps
· Stoplamp switch
· Fog lamp switch
· Multifunction switch
· Light sensor
Lamp Assembly Condensation
Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur if the temperature is cold. When normal condensation occurs, a thin film of mist can form on the interior of the lens. The thin mist eventually clears and exits through the vents during normal operation. Time to clear the lens of acceptable mist varies with ambient humidity and lamp types. Normal condensation clears from any lamp in 48 hours under dry conditions.
Do not replace a lamp assembly with acceptable levels of condensation such as:
· presence of thin mist (no streaks, drip marks or droplets are present)
· fine mist covers less than 50% of the lens
Examples of unacceptable moisture (usually caused by a lamp housing leak):
· water puddling inside the lamp
· large water droplets, drip marks or streaks present on the interior of the lens
The headlamp switch is integrated into the multifunction switch. For additional information, refer to Section
211-05 .
The DRL system operates the low beam headlamps at a reduced intensity. The SJB supplies pulse width modulated (PWM) voltage to the low beam headlamps when the following conditions are met:
· The headlamp switch is not in the HEADLAMPS ON position.
· The ignition switch is in the RUN position.
· The parking brake control is released.
…