Caterpillar 3064 & 3066 Engines Factory Service & Shop Manual
Catalog:
Model:
Complete workshop repair service manual with electrical wiring diagrams for Caterpillar 3064 & 3066 Engines. It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.
This Caterpillar 3064 & 3066 Diesel Engines service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.
1,521 pages, bookmarked, Searchable, Printable, high quality PDF
MANUAL LIST:
SENR5553 - Disassembly & Assembly (3064 & 3066 Engines for Caterpillar Built Machines)
SENR5545 - Specifications (3064 & 3066 Engines for Caterpillar Built Machines)
SENR5546 - Systems Operation (3064 & 3066 Engines for Caterpillar Built Machines)
SENR5546 - Testing & Adjusting (3064 & 3066 Engines for Caterpillar Built Machines)
SENR5545 - Specifications (3064 & 3066 Engines for Caterpillar Built Machines)
Air Inlet Heater.pdf
Alternator and Regulator (1).pdf
Alternator and Regulator (2).pdf
Alternator and Regulator.pdf
Belt Tension Chart.pdf
Belt Tightener.pdf
Camshaft.pdf
Connecting Rod Bearing Journal.pdf
Connecting Rod.pdf
Coolant Temperature Switch.pdf
Crankshaft.pdf
Crankshaft Pulley.pdf
Crankshaft Seals.pdf
Cylinder Block.pdf
Cylinder Head - 3064.pdf
Cylinder Head - 3066.pdf
Electric Starting Motor.pdf
Engine Design (1).pdf
Engine Design (2).pdf
Engine Design.pdf
Engine Oil Bypass Valve.pdf
Engine Oil Pan.pdf
Engine Oil Pressure Sender.pdf
Engine Oil Pressure Switch.pdf
Engine Oil Pump.pdf
Engine Oil Relief Valve.pdf
Exhaust Manifold (1).pdf
Exhaust Manifold (2).pdf
Exhaust Manifold.pdf
Flywheel.pdf
Fuel Filter and Water Separator (1).pdf
Fuel Filter and Water Separator (2).pdf
Fuel Filter and Water Separator.pdf
Fuel Injection Lines.pdf
Fuel Injection Nozzles.pdf
Fuel Injection Pump.pdf
Gear Group (Front).pdf
Lifter Group.pdf
Main Bearing Journal.pdf
Piston and Rings.pdf
Rocker Shaft.pdf
Turbocharger.pdf
Valve Mechanism Cover.pdf
Valve Mechanism.pdf
Water Pump.pdf
Water Temperature Regulator.pdf
SENR5546 - Systems Operation (3064 & 3066 Engines for Caterpillar Built Machines)
Air Inlet and Exhaust System.pdf
Basic Engine.pdf
Cooling System.pdf
Electrical System.pdf
Fuel System.pdf
General Information.pdf
Lubrication System.pdf
SENR5546 - Testing & Adjusting (3064 & 3066 Engines for Caterpillar Built Machines)
Air in Fuel - Test.pdf
Air Inlet and Exhaust System - Inspect.pdf
Alternator - Test.pdf
Battery - Test.pdf
Charging System - Test.pdf
Compression - Test.pdf
Connecting Rod Bearings - Inspect.pdf
Connecting Rod - Inspect.pdf
Cooling System - Check - Overheating.pdf
Cooling System - Inspect.pdf
Cooling System - Test.pdf
Cylinder Block - Inspect.pdf
Cylinder Head - Inspect.pdf
Electric Starting System - Test.pdf
Engine Crankcase Pressure (Blowby) - Test.pdf
Engine Oil Cooler - Inspect.pdf
Engine Oil Pressure - Test.pdf
Engine Oil Pump - Inspect.pdf
Engine Speed - Check.pdf
Engine Valve Lash - Inspect_Adjust.pdf
Engine Valve Lash - InspectAdjust.pdf
Excessive Bearing Wear - Inspect.pdf
Excessive Engine Oil Consumption - Inspect.pdf
Exhaust Temperature - Test.pdf
Finding Top Center Position for No. 1 Piston.pdf
Flywheel Housing - Inspect.pdf
Flywheel - Inspect.pdf
Fuel Injection Nozzle - Test.pdf
Fuel Injection Timing - Check.pdf
Fuel Quality - Test.pdf
Fuel System - Inspect.pdf
Fuel System Pressure - Test.pdf
Fuel System - Prime.pdf
Gear Group (Front) - Time.pdf
Governor - Adjust - In-line Fuel Pump.pdf
High Idle RPM - Adjust.pdf
Increased Engine Oil Temperature - Inspect.pdf
Inlet Manifold Pressure - Test.pdf
Low Idle RPM - Adjust.pdf
Main Bearings - Inspect.pdf
Pinion Clearance - Adjust.pdf
Piston Height - Inspect.pdf
Piston Ring Groove - Inspect.pdf
Troubleshooting.pdf
Turbocharger - Inspect.pdf
Valve Guide - Inspect.pdf
Water Temperature Regulator - Test.pdf
SENR5553 - Disassembly & Assembly (3064 & 3066 Engines for Caterpillar Built Machines)
Air Inlet Heater - Remove and Install.pdf
Alternator - Remove and Install.pdf
Bearing Clearance - Check.pdf
Camshaft Bearings - Install.pdf
Camshaft Bearings - Remove.pdf
Camshaft Gear - Remove and Install.pdf
Camshaft - Install.pdf
Camshaft - Remove.pdf
Connecting Rod Bearings - Install.pdf
Connecting Rod Bearings - Remove.pdf
Coolant Temperature Switch - Remove and Install.pdf
Crankcase Breather - Remove and Install.pdf
Crankshaft Front Seal - Install.pdf
Crankshaft Front Seal - Remove.pdf
Crankshaft Gear - Remove and Install.pdf
Crankshaft - Install.pdf
Crankshaft Main Bearings - Install.pdf
Crankshaft Main Bearings - Remove.pdf
Crankshaft Pulley - Remove and Install.pdf
Crankshaft Rear Seal - Install.pdf
Crankshaft Rear Seal - Remove.pdf
Crankshaft - Remove.pdf
Cylinder Head - Install.pdf
Cylinder Head - Remove.pdf
Cylinder Liner - Install.pdf
Cylinder Liner - Remove.pdf
Electric Starting Motor - Remove and Install.pdf
Engine Oil Bypass Valve - Remove and Install.pdf
Engine Oil Cooler - Assemble.pdf
Engine Oil Cooler - Disassemble.pdf
Engine Oil Cooler - Install.pdf
Engine Oil Cooler - Remove.pdf
Engine Oil Filter Base - Install.pdf
Engine Oil Filter Base - Remove.pdf
Engine Oil Pan - Remove and Install .pdf
Engine Oil Pressure Switch - Remove and Install.pdf
Engine Oil Pump - Install.pdf
Engine Oil Pump - Remove.pdf
Engine Oil Relief Valve - Remove and Install.pdf
Exhaust Manifold - Remove and Install.pdf
Flywheel Housing - Remove and Install .pdf
Flywheel - Install.pdf
Flywheel - Remove.pdf
Front Plate - Install.pdf
Front Plate - Remove.pdf
Fuel Filter Base - Remove and Install.pdf
Fuel Injection Lines - Remove and Install.pdf
Fuel Injection Nozzles - Install.pdf
Fuel Injection Nozzles - Remove.pdf
Fuel Injection Pump - Install.pdf
Fuel Injection Pump - Remove.pdf
Fuel Priming Pump - Remove and Install.pdf
Fuel Shutoff Solenoid - Remove and Install.pdf
Gear Group (Front) - Install - Idler Gear Only.pdf
Gear Group (Front) - Remove - Idler Gear Only.pdf
Housing (Front) - Install.pdf
Housing (Front) - Remove.pdf
Inlet and Exhaust Valve Guides - Remove and Install.pdf
Inlet and Exhaust Valve Seals - Remove and Install.pdf
Inlet and Exhaust Valve Seat Inserts - Remove and Install.pdf
Inlet and Exhaust Valve Springs - Remove and Install.pdf
Inlet and Exhaust Valves - Remove and Install.pdf
Inlet Manifold - Install.pdf
Inlet Manifold - Remove.pdf
Lifter Group - Remove and Install.pdf
Pistons and Connecting Rods - Assemble.pdf
Pistons and Connecting Rods - Disassemble.pdf
Pistons and Connecting Rods - Install.pdf
Pistons and Connecting Rods - Remove.pdf
Rocker Shaft and Pushrod - Install.pdf
Rocker Shaft and Pushrod - Remove.pdf
Rocker Shaft - Assemble.pdf
Rocker Shaft - Disassemble.pdf
Turbocharger - Assemble.pdf
Turbocharger - Disassemble.pdf
Turbocharger - Install.pdf
Turbocharger - Remove.pdf
Valve Mechanism Cover - Remove and Install.pdf
V-Belts - Remove and Install.pdf
Water Pump - Assemble.pdf
Water Pump - Disassemble.pdf
Water Pump - Install.pdf
Water Pump - Remove.pdf
Water Temperature Regulator - Remove and Install.pdf
EXCERPT:
Installation Procedure
NOTICE
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Place the fuel return line (10) in position on the engine. Connect fitting (9) of the fuel return line to the fuel injection pump.
1.
Install the washer and bolt (8) through the clamp in order to secure the fuel return line to the inlet manifold.
2.
Install the fuel return line (10) to the fuel injection nozzles. Secure the fuel return line to the fuel injection nozzle with acorn nuts (7) .
...