Complete workshop repair service manual for Ford Cars & Trucks 2008 Models (Crown Victoria, E-150, E-250, E-350, E-450, Edge, Escape, Escape Hybrid, Expedition, Explorer, Explorer Sport Trac, F-150, F-250, F-350, F-450, F-53 Motorhome Chassis, F-550, F-650, F-750, Focus, Fusion, Grand Marquis, Low Cab Forward, MKX, MKZ, Mariner, Mariner Hybrid, Mark LT, Milan, Mountaineer, Mustang, Navigator, Pre-Delivery, Ranger, Sable, Taurus, Taurus X, Town Car). It's the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.

The workshop manuals for Crown Victoria, E-150, E-250, E-350, E-450, Edge, Escape, Escape Hybrid, Expedition, Explorer, Explorer Sport Trac, F-150, F-250, F-350, F-450, F-53 Motorhome Chassis, F-550, F-650, F-750, Focus, Fusion, Grand Marquis, Low Cab Forward, MKX, MKZ, Mariner, Mariner Hybrid, Mark LT, Milan, Mountaineer, Mustang, Navigator, Pre-Delivery, Ranger, Sable, Taurus, Taurus X, Town Car (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail.

PRODUCT DETAILS:
Total Size: 2.4GB
File Format: DVD iso image
Language: English

MODELS COVERED:
2008 Crown Victoria, 2008 E-150, 2008 E-250, 2008 E-350, 2008 E-450, 2008 Edge, 2008 Escape, 2008 Escape Hybrid, 2008 Expedition, 2008 Explorer, 2008 Explorer Sport Trac, 2008 F-150, 2008 F-250, 2008 F-350, 2008 F-450, 2008 F-53 Motorhome Chassis, 2008 F-550, 2008 F-650, 2008 F-750, 2008 Focus, 2008 Fusion, 2008 Grand Marquis, 2008 Low Cab Forward, 2008 MKX, 2008 MKZ, 2008 Mariner, 2008 Mariner Hybrid, 2008 Mark LT, 2008 Milan, 2008 Mountaineer, 2008 Mustang, 2008 Navigator, 2008 Ranger, 2008 Sable, 2008 Taurus, 2008 Taurus X, 2008 Town Car

EXCERPT (2008 Ford Vehicles (ALL MODELS) Service/Repair Manual):
Piston Pin-to-Piston Clearance

3.8L and 4.6L (2V) Engines

Check the outside diameter of the piston pin and the inner diameter (ID) of the pin bore in the piston as outlined. Replace any piston pin or piston that is not within specifications. For Specifications, refer to Section 03-01A (3.8L) or Section 03-01B (4.6L (2V)).

Piston Outer Diameter

Measure the piston diameter using a micrometer. Measure piston skirt diameter 90 degrees to piston pin centre axis, 42 mm (1.65 inches) from piston dome.

It may be necessary to use another piston (within the same grade size) that is either slightly larger or smaller to achieve the specified clearance.
 
Piston Rings

 CAUTION: Piston rings should not be transferred from one piston to another, regardless of mileage or piston ring failure may occur.

Replace all piston rings that are scored, broken, chipped or cracked. Check the end gap and side clearance as outlined.

Piston Ring-to-Groove Clearance

NOTE: If lower lands have high steps, piston should be replaced.

Check piston ring side clearance of compression rings with Feeler Gauge D81L-4201-A or equivalent inserted between piston ring and its lower land. Gauge should slide freely around entire piston ring circumference without binding. Any wear that occurs will form a step at inner portion of lower land.

If clearance is greater than service limit, replace piston ring. If clearance exceeds service limit, even with a new piston ring, replace piston. Refer to Section 03-01A (3.8L), Section 03-01B (4.6L (2V)) or Section 03-01C (4.6L (4V)).
…